Aller au contenu principal

Ce tutoriel a des changements plus récents. Passer à la dernière version non vérifiée.

Nostalgia Electrics RHP-310 Replacing Housing Replacement

Ce dont vous avez besoin

  1. Nostalgia Electrics RHP-310 Replacing Housing Replacement, Power Switch: étape 1, image 1 de 1
    • Unplug the popper.

    • Lift the lid up to remove it.

  2. Nostalgia Electrics RHP-310 Replacing Housing Replacement: étape 2, image 1 de 1
    • Lay the popper on its side.

    • Remove the five 12mm Philips #2 screws around the perimeter of the base with the Phillips #2 screwdriver.

    • Remove the two 15mm Philips #2 screws in the center of the base with the Phillips #2 screwdriver.

    • Put the removed screws in a safe place, they will be needed later to reattach the housing to the base.

  3. Nostalgia Electrics RHP-310 Replacing Housing Replacement: étape 3, image 1 de 1
    • Flip the base over to view the interior of the base panel.

    • Unscrew the two 10 mm Philips #2 screws from the base panel.

    • Remove the base and set it aside.

  4. Nostalgia Electrics RHP-310 Replacing Housing Replacement: étape 4, image 1 de 2 Nostalgia Electrics RHP-310 Replacing Housing Replacement: étape 4, image 2 de 2
    • Locate the power switch connected to the side of the housing.

    • Pinch the sides of the power switch.

    • Push the power button up and out of the housing.

  5. Nostalgia Electrics RHP-310 Replacing Housing Replacement: étape 5, image 1 de 1
    • Remove the wires connected to the power switch that should be detached from the housing.

    • Gently pry the wires loose from the power switch with the plastic opening tool.

    • The wires should easily pop out from the power switch.

  6. Nostalgia Electrics RHP-310 Replacing Housing Replacement: étape 6, image 1 de 1
    • Remove the power switch from the housing unit.

    • You can now replace the power switch, if necessary.

  7. Nostalgia Electrics RHP-310 Replacing Housing Replacement, Replacing Housing: étape 7, image 1 de 2 Nostalgia Electrics RHP-310 Replacing Housing Replacement, Replacing Housing: étape 7, image 2 de 2
    • Now that the power switch is disconnected from the popper, you will need to remove the white top.

    • Gently remove the heating component from the popper.

    • Unscrew the four screws (11mm Philips #2 screws) that connect the white top to the housing.

  8. Nostalgia Electrics RHP-310 Replacing Housing Replacement: étape 8, image 1 de 1
    • Remove the white top from the housing.

    • Save the screws from previous step. You will need them to connect the new housing to the white top.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Dana Clarke

Membre depuis le 09/26/12

50 Réputation

6 tutoriels rédigés

Équipe

Cal Poly, Team 16-57, Forte Fall 2012 Membre de l'équipe Cal Poly, Team 16-57, Forte Fall 2012

CPSU-FORTE-F12S16G57

5 membres

6 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 1

Total : 501