Introduction

Use this guide to replace a broken mouse buttons controller.

Pièces

Aucune pièce nécessaire.

Turn the laptop upside-down, with the handle facing away from you.
  • Turn the laptop upside-down, with the handle facing away from you.

Ajouter un commentaire

Pull the lock tabs towards the green outer edges of the laptop.
  • Pull the lock tabs towards the green outer edges of the laptop.

  • Hold the left lock tab in the unlock position until the battery is completely removed in the next step.

Ajouter un commentaire

  • Lift up on the middle of the battery to remove it from the device.

Ajouter un commentaire

  • Remove the two 2mm Phillips #1 screws from beneath the battery lock tabs.

Ajouter un commentaire

  • Flip the laptop over to its normal position.

  • Lift the two antennas on both sides to unlock the screen.

  • Open the laptop.

Ajouter un commentaire

  • Be careful not to pull the keyboard too far because there is still a ribbon cable attached to the bottom.

  • Gently lift up on the back of the keyboard.

  • Pull the keyboard up far enough to expose the ribbon cable.

Ajouter un commentaire

  • Gently lift up on the black connector to release the ribbon cable.

  • Gently pull the blue plastic tab up and away from the black connector.

  • Remove the keyboard from the laptop.

Ajouter un commentaire

  • Close and flip the laptop over so you are looking at the battery compartment

  • Remove the five 4mm Phillips #1 screws from inside the battery compartment

Ajouter un commentaire

  • Flip the laptop over, showing the top of the device.

  • Open the laptop and rotate the screen ninety degrees.

  • Tilt the screen so the lower right corner of the screen is closer to the lower case.

Ajouter un commentaire

  • Push in and lift up on the keyboard edge of the white handle piece.

  • Pull the piece towards yourself to remove it from the laptop.

Ajouter un commentaire

  • Remove the four 4mm Phillips #1 screws attaching the green trim to the body of the computer.

Ajouter un commentaire

  • Pry off the rear green trim piece.

Ajouter un commentaire

  • Be careful not to pull the bottom portion of the laptop completely off, as there is a cable connecting it to the laptop.

  • Slide the green trim pieces away from the screen.

  • This should release the entire bottom portion of the laptop.

Ajouter un commentaire

  • Unplug the cable from the mouse buttons controller to completely remove the lower frame from the device.

Ajouter un commentaire

  • Rotate the entire lower assembly up slightly, and pull it away from the screen to free it from the screen hinge.

  • There may be some adhesive holding the cable to the metal plate. Gently pull the cable off of the plate if it is stuck.

Ajouter un commentaire

  • You should now be looking at the bottom of the lower case.

  • Remove the eight 4mm Phillips #1 screws attaching the green trim pieces to the lower frame.

  • Pry off the front and side trim pieces.

Ajouter un commentaire

  • Remove the two 4mm Phillips #1 screws that attach the mouse buttons controller to the lower frame.

Ajouter un commentaire

  • Disconnect the ribbon cable attached to the keyboard compartment.

  • Unplug the ribbon cable between the touchpad and the mouse buttons controller.

  • Remove the mouse buttons controller from the device.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Michael Kellerman

Membre depuis le 24/01/2013

46 Réputation

3 tutoriels rédigés

Équipe

Cal Poly, Team 3-30, Amido Winter 2013 Membre de l'équipe Cal Poly, Team 3-30, Amido Winter 2013

CPSU-AMIDO-W13S3G30

3 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 0

Total : 165