Introduction

Learn how to install a wireless card into the OLPC XO-4 Touch.

Pièces

Aucune pièce nécessaire.

  1. Turn the laptop upside-down, with the handle facing away from you.
    • Turn the laptop upside-down, with the handle facing away from you.

    Ajouter un commentaire

  2. Pull the lock tabs towards the green outer edges of the laptop.
    • Pull the lock tabs towards the green outer edges of the laptop.

    • Hold the left lock tab in the unlock position until the battery is completely removed in the next step.

    Ajouter un commentaire

    • Lift up on the middle of the battery to remove it from the device.

    Ajouter un commentaire

    • Remove the two 4mm Phillips #1 screws underneath the screen on the right-hand side.

    • Rotate the screen 180° and remove the other two screws.

    • You will have to put your screwdriver through the handle in order to reach the middle screw for both sides.

    Ajouter un commentaire

    • Remove the green side panel by pressing down on the small green button on the top and sliding the panel up.

    • Repeat the step above for the panel on the other side.

    Ajouter un commentaire

    • Be careful not to pull the bottom too far out because a ribbon cable is under the frame and can easily break.

    • Gently lift up the lower part of the frame and pull it down to free the screen frame.

    Ajouter un commentaire

  3. Répandez la magie de Noël
    Obtenez 12 $ de réduction sur les commandes de 50 $ ou plus avec le code FIXMAS12
    Répandez la magie de Noël
    Obtenez 12 $ de réduction sur les commandes de 50 $ ou plus avec le code FIXMAS12
    • Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame.

    Ajouter un commentaire

    • Remove the four 7.62mm screws using a Phillips #1 screwdriver.

    Ajouter un commentaire

    • Be careful not to pull the screen out too far. There are two ribbon cables attached to the screen, and they can easily break.

    • Carefully lift the screen out.

    Ajouter un commentaire

    • Notice that the laptop in this picture has been turned 180° with the antennas now below the screen.

    • For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs.

    Ajouter un commentaire

    • Remove the screen from the laptop.

    Ajouter un commentaire

    • Remove the four 6mm screws using a Phillips #1 screwdriver.

    Ajouter un commentaire

    • Rotate the top half of the laptop so that the back cover is facing you.

    • Pull up the tabs on the lower part of the back cover and pull it down and away from the antennas.

    • Remove the back cover by gently lifting it off of the laptop.

    Ajouter un commentaire

    • When pulling out the connectors, make sure to hold the metal connector instead of the wire.

    • Gently pull out the two antenna connectors by pulling them away from the motherboard.

    Ajouter un commentaire

    • Remove the black 4mm Phillips #1 screw holding the wireless card in.

    Ajouter un commentaire

    • Remove the wireless card from the laptop by gently sliding it out of its socket.

    Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Zach Yasuda

Membre depuis le 24/01/2013

173 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 3-29, Amido Winter 2013 Membre de l'équipe Cal Poly, Team 3-29, Amido Winter 2013

CPSU-AMIDO-W13S3G29

4 membres

10 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 2

Total : 209