Introduction

This guide will give step-by-step instructions on how to install a LCD screen in a Olympus D590 camera.

Flip camera so you are looking at the bottom.
  • Flip camera so you are looking at the bottom.

  • Unscrew all 5 base plate screws.

Ajouter un commentaire

Lift open retainer clip by sliding the clip to the left and letting the clip pop up.
  • Lift open retainer clip by sliding the clip to the left and letting the clip pop up.

Ajouter un commentaire

  • Unscrew the single screw located next to the battery slot.

Ajouter un commentaire

  • Turn the camera so that the USB, AV and DC in/out rubber plate it facing you.

  • Lift the rubber plate exposing the ports beneath.

Ajouter un commentaire

  • Unscrew the 2 screws next to the USB and AC ports.

Ajouter un commentaire

  • Use a flathead screwdriver or another flat opening tool to pry the faceplate from the whole device.

Ajouter un commentaire

  • Pull off the faceplate to reveal the inside of the camera.

  • Be careful of the connector that goes from the faceplate to the motherboard . Disconnecting this line will cause the camera not not power on through the on/off switch anymore.

Ajouter un commentaire

  • Use a phillips head screwdriver to remove the 3 screws highlighted in the picture.

Ajouter un commentaire

  • Unscrew the 2 screws located on either side of the flash.

Ajouter un commentaire

  • Get a flathead screwdriver or an iPod opening tool (both are shown in this picture).

  • Carefully pry off the blackplate from the remaining part of the camera.

Ajouter un commentaire

  • Pull the backplate off.

Ajouter un commentaire

  • Unscrew the screw shown in the picture from LCD screen.

Ajouter un commentaire

  • Remove the side pannel by sliding it off the body of the camera.

  • Lift the camera no more than 3cm to make sure all screws have been taken off.

Ajouter un commentaire

  • Flip camera so you are looking at the front.

  • Remove gray and blue wiring with tweasers by gently wiggling and pulling.

  • Be careful not to rip the wiring tape with the tweezers.

Ajouter un commentaire

  • Locate the tape securing the wiring with the gray end piece located on top of the camera.

  • Gently lift up on the tape till all wires are exposed.

Ajouter un commentaire

  • Flip Camera to the bottom side as shown.

  • Pull and wriggle the thin yellow wiring tape to detach it from the rest of the camera, while leaving it attached to the LCD screen.

Ajouter un commentaire

  • Flip camera so the front is facing you.

  • Locate speaker in upper right hand corner.

  • Gently lift with tweasers.

  • Feed wiring through designated spot so that it is no longer connected to the camera.

Ajouter un commentaire

  • Lift the LCD screen so the thick yellow wiring is the only thing attaching the LCD screen to the camera.

  • Gently pull the thick yellow wiring out by using the forefinger and thumb.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Sara

Membre depuis le 15/04/2010

84 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 28-23, Regan Spring 2010 Membre de l'équipe Cal Poly, Team 28-23, Regan Spring 2010

CPSU-REGAN-S10S28G23

4 membres

7 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 0

Total : 1,893