Réparez vos affaires Communauté Boutique

Olympus Stylus Tough TG-2 iHS Battery and Connector Seals Replacement

Introduction

Have your seals been damaged? It may be time to replace them. This guide will walk you through the simple steps to access and replace your battery and connector cover seals.

Ce dont vous avez besoin

  1. Olympus Stylus Tough TG-2 iHS Battery and Connector Seals Replacement, Battery and Connector Seals: étape 1, image 1 de 3 Olympus Stylus Tough TG-2 iHS Battery and Connector Seals Replacement, Battery and Connector Seals: étape 1, image 2 de 3 Olympus Stylus Tough TG-2 iHS Battery and Connector Seals Replacement, Battery and Connector Seals: étape 1, image 3 de 3

    • Locate the battery/card cover on the bottom of the camera. .

    • Slide the tab labeled lock to show orange.

    • Slide the battery/card cover lock to revile orange and the door will spring open.

    Modifier

  2. Olympus Stylus Tough TG-2 iHS Battery and Connector Seals Replacement: étape 2, image 1 de 3 Olympus Stylus Tough TG-2 iHS Battery and Connector Seals Replacement: étape 2, image 2 de 3 Olympus Stylus Tough TG-2 iHS Battery and Connector Seals Replacement: étape 2, image 3 de 3

    • Remove the 2 Phillips #00 screws on the inner battery door.

    • Use a spudger to release the seal and metal clip.

    • Replace the seal.

    Modifier

  4. Olympus Stylus Tough TG-2 iHS Battery and Connector Seals Replacement: étape 3, image 1 de 2 Olympus Stylus Tough TG-2 iHS Battery and Connector Seals Replacement: étape 3, image 2 de 2

    • Locate the connector cover on the side of the camera.

    • Slide the tab labeled lock to show orange.

    • Slide the connector cover lock to revile orange and the door will spring open.

    Modifier

  5. Olympus Stylus Tough TG-2 iHS Battery and Connector Seals Replacement: étape 4, image 1 de 3 Olympus Stylus Tough TG-2 iHS Battery and Connector Seals Replacement: étape 4, image 2 de 3 Olympus Stylus Tough TG-2 iHS Battery and Connector Seals Replacement: étape 4, image 3 de 3

    • Remove the 2 Phillips #00 screws on the inner connector door.

    • Use a spudger to release the seal, the clear plastic piece, and the metal piece.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 3 autres contributeurs

Amanda

Membre depuis le 07/20/15

933 Réputation

8 tutoriels rédigés

Badges: 11

+ 8 badges supplémentaires

Équipe

Eastern Washington University, Team 1-5, Carnegie Fall 2015 Membre de l'équipe Eastern Washington University, Team 1-5, Carnegie Fall 2015

EWU-CARNEGIE-F15S1G5

3 membres

16 tutoriels rédigés

3 commentaires

Where can I get the seals?

Ahmed - Réponse

I have the same question. Where can I buy the seals? Olymus service man told me it is not possible to buy, and that I have to send TG-2 to service and pay about 100$.

adan - Réponse

OK. Great instructions. I think I could do this, but where do I get the seals?

Steve Tobin - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 9

Total : 2,038