OnePlus 6T Rear Camera Replacement

Introduction

OnePlus 6T was the flagship killer launched by the Chinese brand in November 2018. One of the major upgrades from its OnePlus 6 model, was the in-screen fingerprint scanner alongside other hardware updates. 6T featured a dual-camera setup at the rear (16+20 MP) and was the best camera launched by the company until the OnePlus 7 in the following year. This post helps you replace that setup and its detailed explanation ensures that you perform this procedure in the best way possible.

Ce dont vous avez besoin

Étape 1 Back Cover

OnePlus 6T Rear Camera Replacement, Back Cover: étape 1, image 1 de 1

Make sure the phone is powered off and placed with the back cover facing towards you on a stable surface.

Modifier

Étape 2

Pop open the SIM card tray by inserting a SIM card removal tool into a small hole on the upper-left side of the phone.
Carefully remove the SIM card from its tray.

Modifier

Remove the SIM card tray from the phone. Don't need to remove the actual card from the tray, just be careful you don't lose it…

SayIDidIt™ - 13 févr. 2022 Réponse

Étape 3

Loosen the binding glue within the phone using a hairdryer or an iOpener.
If you choose to use a hairdryer, hold the dryer at least eight inches from the phone and apply heat for two minutes in a circular motion around the edges of the phone.

Modifier

Étape 4

OnePlus 6T Rear Camera Replacement: étape 4, image 3 de 3

Outil utilisé dans cette étape :

Plastic Cards

$2.99

J'achète

Insert a Jimmy under one of the heated corners of the phone to lift it slightly.
Insert a plastic card underneath the slightly lifted lip on the back cover and gently glide the card under the lifted phone casing.
There will be a small amount of tension, but this is normal as the card is removing the adhesive within the phone.
Remove the back cover from the phone.
Use high concentration (>90%) isopropyl alcohol and a lint-free cloth to remove all adhesive residue from the back cover and the frame.

Modifier

Do you need to replace the glue when reassembling?

S Marlin - 4 mai 2021 Réponse

It was sufficient for me to re-heat the adhesive from the phone.

Also, I used a pair of tweezers to lift the initial corner, which was a breeze compared to the Jimmy’s as suggested by the guide.

Michel Rummens - 21 oct. 2021 Réponse

The gaps were very tight. After warming the adhesive, it was helpful to have a helper use a suction cup to tug on the back to enlarge the gap for the jimmy.

tbrannam - 31 mai 2022 Réponse

Theres a big patch of glue on the right side of the camera. Be careful with this part, cuz ure proabably under the curved side trying to get inbetween and in my case this shattered the coating of the backside of my phone. It still works, but it has a spider skin on the back now.

Shwyne - 23 janv. 2024 Réponse

Étape 5 Front Camera

OnePlus 6T Rear Camera Replacement, Front Camera: étape 5, image 1 de 2

OnePlus 6T Rear Camera Replacement, Front Camera: étape 5, image 2 de 2

Remove the single 3mm Phillips #00 screws holding the metal battery cover on the phone.
Use tweezers to remove the battery cover and place it to the side.

Modifier

Étape 6

Remove eight 3mm Phillips #00 screws that connect the midframe to the phone.

Modifier

Étape 7

Using a spudger, gently remove the midframe and place it to the side.

Modifier

Étape 8

Using a spudger, lift the light brown tab in the middle of phone to disconnect the front camera.
Remove the front camera from the phone.

Modifier

Étape 9 Motherboard

OnePlus 6T Rear Camera Replacement, Motherboard: étape 9, image 1 de 2

OnePlus 6T Rear Camera Replacement, Motherboard: étape 9, image 2 de 2

Remove the single 3mm Phillips #00 screw to the right of the top rear camera.

Modifier

Étape 10

Using a spudger, disconnect the charging port flex connector, the main flex connector, and the screen flex connector at the bottom of the camera.

Modifier

Étape 11

Use a spudger to disconnect the signal cables on the right side of the motherboard.

Modifier

Étape 12

Disconnect the slider from the top of the phone with a spudger.
The slider is extremely delicate, so it is important you do not attempt to remove it from the sides.
Gently pull the motherboard from the left side and remove it from the phone.