Réparez vos affaires Communauté Boutique

Oster 3905 Lever Spring Replacement

Introduction

This guide will show you how to replace the lever springs on your Oster 3905 toaster.

Ce dont vous avez besoin

  1. Oster 3905 Lever Spring Replacement, Slot Levers: étape 1, image 1 de 1

    • Firmly grip your hand around the slot lever.

    Modifier

  2. Oster 3905 Lever Spring Replacement: étape 2, image 1 de 1

    • Stabilize the toaster by placing your hand on top.

    Modifier

  3. Oster 3905 Lever Spring Replacement: étape 3, image 1 de 2 Oster 3905 Lever Spring Replacement: étape 3, image 2 de 2

    • Forcefully pull the slot lever away from the toaster by keeping parallel to the table.

    Modifier

  4. Oster 3905 Lever Spring Replacement: étape 4, image 1 de 1

    • Both slot levers can be removed.

    Modifier

  5. Oster 3905 Lever Spring Replacement, Outer Shell: étape 5, image 1 de 1

    • Place the toaster upside down so the bottom is facing the ceiling.

    Modifier

  6. Oster 3905 Lever Spring Replacement: étape 6, image 1 de 2 Oster 3905 Lever Spring Replacement: étape 6, image 2 de 2

    • Take off both rubber feet using a small metal spudger.

    • Wedge a spudger under the feet and pull up to pop off.

    Modifier

  8. Oster 3905 Lever Spring Replacement: étape 7, image 1 de 1

    • Use a PH#2 screw bit to remove eight 12mm screws that are located around the perimeter.

    • There are two screws under the rubber feet.

    Modifier

  9. Oster 3905 Lever Spring Replacement: étape 8, image 1 de 1

    • Place the toaster right side up.

    Modifier

  10. Oster 3905 Lever Spring Replacement: étape 9, image 1 de 2 Oster 3905 Lever Spring Replacement: étape 9, image 2 de 2

    • Grab the outer shell firmly and pull up towards the face of the toaster.

    Modifier

  11. Oster 3905 Lever Spring Replacement: étape 10, image 1 de 1

    • For this part, you might need to wiggle the toaster to get the outer shell off.

    • The shell will not completely come off until the motherboard is removed in the next step.

    Modifier

  12. Oster 3905 Lever Spring Replacement: étape 11, image 1 de 3 Oster 3905 Lever Spring Replacement: étape 11, image 2 de 3 Oster 3905 Lever Spring Replacement: étape 11, image 3 de 3

    • Use a J1 screw bit to unscrew eight 8mm screws from the motherboard.

    Modifier

  13. Oster 3905 Lever Spring Replacement: étape 12, image 1 de 2 Oster 3905 Lever Spring Replacement: étape 12, image 2 de 2

    • Take out the grey “cancel” and “bagel” buttons from the shell.

    Modifier

  14. Oster 3905 Lever Spring Replacement, Lever Spring: étape 13, image 1 de 2 Oster 3905 Lever Spring Replacement, Lever Spring: étape 13, image 2 de 2

    • Use the plastic opening tool to remove the top metal panel by prying the 4 top metal tabs upwards. They will be able to slide through the openings and be pulled upwards.

    Modifier

  15. Oster 3905 Lever Spring Replacement: étape 14, image 1 de 2 Oster 3905 Lever Spring Replacement: étape 14, image 2 de 2

    • Once the top metal panel is unhooked, lift and let it hang off the side of the toaster.

    Modifier

  16. Oster 3905 Lever Spring Replacement: étape 15, image 1 de 3 Oster 3905 Lever Spring Replacement: étape 15, image 2 de 3 Oster 3905 Lever Spring Replacement: étape 15, image 3 de 3

    • Use a metal spudger to pry the 8 tabs upwards along the metal that separates the two slots.

    • Pull the metal spacer upwards to release from the toaster.

    Modifier

  17. Oster 3905 Lever Spring Replacement: étape 16, image 1 de 2 Oster 3905 Lever Spring Replacement: étape 16, image 2 de 2

    • Remove the spring wrapped around a metal rod at the front of the toaster, located behind the white plastic lever holder.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 2 autres contributeurs

Sydney Alcaraz

Membre depuis le 09/12/16

601 Réputation

3 tutoriels rédigés

Badges: 10

+ 7 badges supplémentaires

Équipe

CSU Fullerton, Team 2-1, Bruce Fall 2016 Membre de l'équipe CSU Fullerton, Team 2-1, Bruce Fall 2016

CSUF-BRUCE-F16S2G1

5 membres

6 tutoriels rédigés

2 commentaires

Where's the fix?

D Unger - Réponse

Yeah. You just remove the spring? And then what? Surely removing the spring is not the fix.

kryshu - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 1

30 derniers jours : 14

Total : 2,923