Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Ce dont vous avez besoin

  1. Cette étape n’est pas traduite. Aidez à la traduire

    , Batterie: étape 1, image 1 de 2 , Batterie: étape 1, image 2 de 2
    • Press the button securing the battery door to the PSP 300xc, and lift the battery door off.

    • Lift the battery out of the PSP.

  2. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 2, image 1 de 1
    • Use a spudger or your fingernail to remove the warranty sticker stuck to the inside of the battery tray

  3. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 3, image 1 de 2 : étape 3, image 2 de 2
    • Remove four Phillips screws from the back of the PSP.

  4. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 4, image 1 de 1
    • Remove two Phillips screws from the top of the PSP.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 5, image 1 de 1
    • Remove a single screw from the bottom edge of the PSP.

  6. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 6, image 1 de 2 : étape 6, image 2 de 2
    • Insert a spudger between the front case and PSP, and slide the spudger along the perimeter of the front case to remove it.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 7, image 1 de 1
    • Remove a single Phillips screw securing the home bar to the PSP 300xc.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 8, image 1 de 2 : étape 8, image 2 de 2
    • Push the home bar to the right about 1cm to release a tab, and begin to lift the right end of the home bar slightly.

    • Do not attempt to remove the home bar yet, it is still attached to the PSP 300xc.

  9. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 9, image 1 de 1
    • Insert a spudger under the LCD, beside the black plastic tab.

    • Push the LCD to the left and pry up to release the left edge of the LCD from under the plastic tab.

  10. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 10, image 1 de 1
    • Insert a spudger under the LCD, beside the black plastic tab.

    • Push the LCD to the right and pry up to release the right edge of the LCD from under the plastic tab.

  11. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 11, image 1 de 3 : étape 11, image 2 de 3 : étape 11, image 3 de 3
    • Rotate the LCD away from the PSP to reveal the LCD and home bar ribbon cables.

    • Use your fingernail or the edge of a plastic opening tool to flip up the retaining flap on the following four ZIF connectors:

    • Home bar cable

    • Microphone cable

    • LCD display data cable

    • Touchscreen cable

    • Be sure you are prying up on the retaining flap, not the socket itself

    • After flipping up the locking tabs on all four connectors, use your fingers or a spudger to gently pull the cables straight out of the connectors.

  12. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 12, image 1 de 1
    • Remove the LCD from the PSP 300xc.

  13. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 13, image 1 de 3 : étape 13, image 2 de 3 : étape 13, image 3 de 3
    • Lift the home bar up as high as it will go, but not so high that the wires disconnect.

    • Try to bend the small tab under the silver rim as little as possible it the following steps. The more you bend, the more likely it will snap.

    • Twist the home bar counter clockwise while carefully lifting it further. The left edge has to lift over the black plastic frame to allow it to rotate.

    • The home bar should now lift out of the PSP 300xc.

  14. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 14, image 1 de 1
    • Using the flat edge of a spudger, pry the power board away from the PSP 300xc.

  15. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 15, image 1 de 1
    • Lift the right silver rim up and off the PSP 300xc.

  16. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 16, image 1 de 1
    • Using the pointed end of a spudger, pull the UMD door spring to the left, and remove it from the PSP.

  17. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 17, image 1 de 3 : étape 17, image 2 de 3 : étape 17, image 3 de 3
    • Use your fingernail or the edge of a spudger to flip up the retaining flap on the UMD drive ribbon socket.

    • Be sure you are prying up on the retaining flap, not the socket itself

    • Use your fingernail or tip of a spudger to push both sides of the black retaining flap on the UMD laser ribbon socket to the right.

    • Use a spudger to gently pull both ribbon cables straight out of their sockets.

  18. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 18, image 1 de 2 : étape 18, image 2 de 2
    • Flip the PSP 300xc over and open the UMD door.

    • Using a pair of tweezers, grab the small rubber square between the metal UMD brace and case, and lift it out of the PSP 300xc.

    • Repeat for the rubber square on the other side of the UMD door.

  19. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 19, image 1 de 3 : étape 19, image 2 de 3 : étape 19, image 3 de 3
    • Slide the UMD brace toward the top of the UMD door until the brace disconnects from the door. Remove the brace.

  20. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 20, image 1 de 2 : étape 20, image 2 de 2
    • Bend the PSP 300xc case while pulling up on the right edge of the UMD door until the right edge lifts free.

    • Remove the UMD door.

  21. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 21, image 1 de 1
    • Remove the four Phillips screws securing the UMD drive to the PSP 300xc.

  22. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 22, image 1 de 1
    • Lift the UMD drive out of the PSP 300xc, minding any cables that may get caught.

Ligne d'arrivée

2 autres ont terminé cette réparation.

Matthew Newsom

Membre depuis le 01/05/10

39 452 Réputation

67 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 8

30 derniers jours : 65

Total : 7,704