Aller au contenu principal

Ce tutoriel a des changements plus récents. Passer à la dernière version non vérifiée.

Palm TX Power Button Replacement

Ce dont vous avez besoin

  1. Palm TX Power Button Replacement, Back Panel: étape 1, image 1 de 2 Palm TX Power Button Replacement, Back Panel: étape 1, image 2 de 2
    • Orient the device so that the display faces forward.

    • Remove the stylus from the right side.

  2. Palm TX Power Button Replacement: étape 2, image 1 de 1
    • Turn over the device so that the back panel faces forward.

    • Use a T5 Torx screwdriver to remove the four 6.35mm corner screws.

  3. Palm TX Power Button Replacement: étape 3, image 1 de 2 Palm TX Power Button Replacement: étape 3, image 2 de 2
    • Rotate the device so that the display faces forward.

    • Insert a plastic opening tool with the angled tip pointing downward into the crevice on the left side of the device.

    • Pry along the crevice to loosen the back panel.

    • Repeat this process for the right side.

  4. Palm TX Power Button Replacement: étape 4, image 1 de 2 Palm TX Power Button Replacement: étape 4, image 2 de 2
    • Carefully pry the back panel to open the device.

    • Be careful not to break the wire that connects the battery pack to the motherboard.

    • When reassembling, snap the back panel back into place and then insert the top cover.

  5. Palm TX Power Button Replacement: étape 5, image 1 de 2 Palm TX Power Button Replacement: étape 5, image 2 de 2
    • Use a plastic opening tool to peel the battery pack from the back panel.

    • The battery pack is glued to the back panel so removing it may require considerable effort.

  6. Palm TX Power Button Replacement, Battery Pack: étape 6, image 1 de 2 Palm TX Power Button Replacement, Battery Pack: étape 6, image 2 de 2
    • Use a soldering iron to disconnect the battery wires from the motherboard.

    • For soldering instructions, you can view the Soldering Guide.

  7. Palm TX Power Button Replacement, Motherboard: étape 7, image 1 de 2 Palm TX Power Button Replacement, Motherboard: étape 7, image 2 de 2
    • Pull straight up on the ribbon cables located on the bottom right of the motherboard to disconnect them.

  8. Palm TX Power Button Replacement: étape 8, image 1 de 2 Palm TX Power Button Replacement: étape 8, image 2 de 2
    • Lift the mother board out of the device.

    • A weak adhesive attaches the motherboard to the device.

    • The red wire in the picture will not be attached to your device at this point.

  9. Palm TX Power Button Replacement, Power Button: étape 9, image 1 de 1
    • Flip the motherboard so that the black rubber cover faces upward. The power switch is in the top right corner.

    • Remove the button with a soldering iron.

    • For soldering instructions, view the Soldering Guide.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Spencer Lewson

Membre depuis le 01/19/11

793 Réputation

6 tutoriels rédigés

Équipe

Cal Poly, Team 1-15, Amido Winter 2011 Membre de l'équipe Cal Poly, Team 1-15, Amido Winter 2011

CPSU-AMIDO-W11S1G15

4 membres

7 tutoriels rédigés

2 commentaires

what do i do after i remove said button?

Dewm - Réponse

what do i do aftert i desolder the button

Dewm - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 14

Total : 3,292