Introduction

Fixing the lens apparatus on your camera.

Pièces

Aucune pièce nécessaire.

Slide the lock into the unlock position.In this case you would need to slide the lock to the right.
  • Slide the lock into the unlock position.In this case you would need to slide the lock to the right.

  • Use your finger to slide battery hatch towards the arrow sign.

  • Both battery and memory card should now be visible.

Ajouter un commentaire

Open battery hatch and the black cover to expose the battery compartment.
  • Open battery hatch and the black cover to expose the battery compartment.

  • The camera used to create these repair guides did not have a battery and memory card.

  • Pull the battery out and replace with a new one.

  • When putting the battery back in, make sure it is in the same orientation as before.

  • Close the battery compartment and make sure the lock is in the locked position.

Ajouter un commentaire

  • Remove the two 2.8 mm Phillips screws as shown in picture.

Ajouter un commentaire

  • Using a Philips Screw Driver, remove the three 2.8 mm Phillips screws on the bottom of the camera as shown in picture.

Ajouter un commentaire

  • Remove the two 2.8 mm Phillips screws on the side of the camera as shown in picture. /state that a screwdriver is needed in the step.

Ajouter un commentaire

  • Use a Spudger tool to pry open case from all sides./No edits necessary

Ajouter un commentaire

  • Beware of yellow film strip when opening./Caution: Beware of the yellow film strip when opening the casing of the camera, make this caution notice a different color.

  • Use your fingers to carefully pry off the back casing from the camera assembly/. No edits necessary.

Ajouter un commentaire

  • Lay the camera on its front side./combine this sentence to the step below.

  • Use Spudger tool to open the film strip locking mechanism and remove strip./No edits necessary.

  • Hold down on the camera's metal casing with one hand. Using your other hand, completely lift the back case off the rest of the camera, making sure the film strip separates./Make a picture for this step.

Ajouter un commentaire

  • Remove the two remaining 2.8 mm Phillips screws on the bottom of the camera.

  • The other three screws shown in picture were removed to take off the back case.

Ajouter un commentaire

  • Using Spudger tool, pry the front case from the camera's components.

  • Use your fingers to carefully pull the back case from the front case.

  • Cut the black and red wires connecting front case to the body of the camera.

  • Being careful nothing get's caught, separate the front case from the camera.

  • To put the new front case back on, solder the wires of the new front case to the components of the camera.

Ajouter un commentaire

  • Check the "V" shaped spring to see if it is connected at shown location.

Ajouter un commentaire

  • Manually move the Lens Apparatus from the inside to shown position.

  • Check to see if the spring is aligned correctly and lens opens.

  • If not, you will need to take out the spring and place it into the proper position, or get a new spring all together.

  • To reassemble your device, follow these instructions in reverse order.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Alex Penman

Membre depuis le 28/01/2011

463 Réputation

4 tutoriels rédigés

Équipe

Cal Poly, Team 7-35, Regan Winter 2011 Membre de l'équipe Cal Poly, Team 7-35, Regan Winter 2011

CPSU-REGAN-W11S7G35

4 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 0

Total : 1,164