Menu 

Vos paramètres

Mon établi

Accédez rapidement aux tutoriels, aux pièces et aux réponses correspondant à vos appareils
Mon panier (US Store)

On dirait que votre panier est vide

Parcourez notre boutique

Panasonic Lumix DMC-FX07 Back Cover Replacement

En vedette

Rédigé par : Karissa (et 6 autres contributeurs)
  • Commentaires : 0
  • Favoris : 1

Tutoriel vedette

Difficulté

Facile

Étapes

7

Temps nécessaire

3 - 5 minutes

Sections

3

Drapeaux

1

Featured Guide

Tutoriel vedette

L'équipe iFixit trouve ce tutoriel particulièrement réussi.

Introduction

This guide will show you how to remove the back panel of your camera.

Outils

Acheter ces outils

Pièces

Aucune pièce spécifiée.

  1. Move the switch on the battery door to the Open position.

    • Move the switch on the battery door to the Open position.

    • The door will automatically swing open after you let it go.

    Modifier

  2. Push the small gray tab on the top right corner to the left. The battery will pop out slightly. Keep your finger clear of the battery when it pops out.

    • Push the small gray tab on the top right corner to the left. The battery will pop out slightly.

    • Keep your finger clear of the battery when it pops out.

    Modifier

  3. Push the memory card in and let go.

    • Push the memory card in and let go.

    • The memory card will pop out slightly.

    • Pull out the memory card.

    Modifier

  4. Fix Kits pour Android

    A new screen or battery is one kit away.

    Acheter maintenant

    Fix Kits pour Android

    A new screen or battery is one kit away.

    Acheter maintenant

  5. Unscrew the small screws on the sides of the camera. The screws on the left side(#00P, 4.7mm) are longer than the screw on the right side(#00P, 3.3mm).

    • Unscrew the small screws on the sides of the camera.

    • The screws on the left side(#00P, 4.7mm) are longer than the screw on the right side(#00P, 3.3mm).

    Modifier

  6. Unscrew the three small screws on the bottom(#00P, 3.3mm). The bottom will fall off.

    • Unscrew the three small screws on the bottom(#00P, 3.3mm).

    • The bottom will fall off.

    Modifier

  7. Lift up the bottom back cover by prying the bottom edge with the spudger. Gently lift up the back cover with your hand from the bottom to the top. Gently lift up the back cover with your hand from the bottom to the top.

    • Lift up the bottom back cover by prying the bottom edge with the spudger.

    • Gently lift up the back cover with your hand from the bottom to the top.

    Modifier

  8. Lift the tabs on the ZIF connectors. The ribbon cables should easily come out of the ZIF connectors. The ribbon cables should easily come out of the ZIF connectors.

    • Lift the tabs on the ZIF connectors.

    • The ribbon cables should easily come out of the ZIF connectors.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 6 autres contributeurs

Karissa

Membre depuis le 13/04/2012

50 Réputation

8 tutoriels rédigés

Badges: 10

+ 7 badges supplémentaires

Équipe

Cal Poly, Team 6-23, Amido Spring 2012 Membre de l'équipe Cal Poly, Team 6-23, Amido Spring 2012

CPSU-AMIDO-S12S6G23

4 membres

10 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 3

Total : 1,120