Introduction

Use this guide to replace the mainboard and navigation board in your Parrot AR.Drone 2.0.

AR.Drone 2.0 spare parts and mounting tools are available from several Parrot retailers.

Vidéo d'introduction

Remove the foam body.
  • Remove the foam body.

Ajouter un commentaire

Disconnect the battery by pulling the two red wires apart.
  • Disconnect the battery by pulling the two red wires apart.

  • Remove the battery by releasing the battery retaining straps.

Ajouter un commentaire

  • Turn the drone upside down.

  • The cover is held on by plastic tape. Peel off the tape and use a spudger to remove the back cover.

Ajouter un commentaire

  • Using a spudger, separate the connector for the downward camera.

  • Remove the camera from the body by pulling it off the foam body.

Ajouter un commentaire

  • Use a spudger to release the black retaining clip. Then disconnect the connector to the sensors.

  • Use tweezers to carefully remove the ribbon from the connector.

Ajouter un commentaire

  • Remove the four 8mm torx screws with a T6 bit.

  • Remove the four 8mm philips head screws with a PH00 bit.

Ajouter un commentaire

  • Carefully pull the secondary board from the mainboard.

Ajouter un commentaire

  • Turn the drone right side up

  • Remove the USB connector from the battery retaining straps.

Ajouter un commentaire

  • Release the rubber clip holding the USB and battery power cable to the body.

Ajouter un commentaire

  • Avoid using sharp tools near the battery.

  • Push the USB and power cable through the battery panel.

Ajouter un commentaire

  • Turn the drone upside down again.

  • Use a spudger to release the connector and carefully remove the ribbon.

Ajouter un commentaire

  • Lift the mainboard up so that you can access the back.

  • Disconnect the first connector with the white wires using a nylon spudger.

  • Disconnect the second connector with the red and black wires using a spudger.

Ajouter un commentaire

  • The mainboard is now fully detached and can be removed.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

David Hoyt

Membre depuis le 09/04/2010

3 626 Réputation

43 tutoriels rédigés

Équipe

Cal Poly, Team 25-89, Amido Spring 2010 Membre de l'équipe Cal Poly, Team 25-89, Amido Spring 2010

CPSU-AMIDO-S10S25G89

4 membres

52 tutoriels rédigés

hey man, you make it too easy

ydebancangancity - Réponse

Hi i am in need of the mainboard. I dnt know where i can buy 1. Any advice

Fugee Maoza - Réponse

I WISH I knew if this would solve my drone issues. I am a disabled teacher & biologist. I was bought the AR drone 2.0 to help keep me in good spirit as I no longer had the strength 2 hold a dslr steady. My father set everything up and he had 1 successful flight. The second flight my dad again just wanted 2 do a simple flight and it just dropped out of the air from 5 feet into grass. IT HAS NEVER WORKED SINCE :( We tried the local hobby store where

I purchased got no help only wanting 2 sell new drones. We get a message saying "UNKNOWN ERROR" since 2013 or 14 I think i have tried everything that you tube says 2 check. : No broken crossbars, blades,gears etc. Resetting will get rid of warning then will not get more that 1ft off the ground and then goes where it wants once it even held its altitude.

So any help is gr8t. Don't have $ to waist with all medical care

Brett Cihlar - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 3

7 derniers jours : 16

30 derniers jours : 65

Total : 3,920