Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the battery by pulling the two red wires apart.
-
Remove the battery by releasing the battery retaining straps.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the drone upside down.
-
The cover is held on by plastic tape. Peel off the tape and use a spudger to remove the back cover.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using a spudger, separate the connector for the downward camera.
-
Remove the camera from the body by pulling it off the foam body.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to release the black retaining clip. Then disconnect the connector to the sensors.
-
Use tweezers to carefully remove the ribbon from the connector.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four 8mm torx screws with a T6 bit.
-
Remove the four 8mm philips head screws with a PH00 bit.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Carefully pull the secondary board from the mainboard.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the drone right side up
-
Remove the USB connector from the battery retaining straps.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Release the rubber clip holding the USB and battery power cable to the body.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Push the USB and power cable through the battery panel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the drone upside down again.
-
Use a spudger to release the connector and carefully remove the ribbon.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the mainboard up so that you can access the back.
-
Disconnect the first connector with the white wires using a nylon spudger.
-
Disconnect the second connector with the red and black wires using a spudger.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
The mainboard is now fully detached and can be removed.
-
Annulation : je n'ai pas terminé ce tutoriel.
4 autres ont terminé cette réparation.
Équipe
Cal Poly, Team 25-89, Amido Spring 2010 Membre de l'équipe Cal Poly, Team 25-89, Amido Spring 2010
CPSU-AMIDO-S10S25G89
4 membres
63 tutoriels rédigés
3 commentaires
hey man, you make it too easy
Hi i am in need of the mainboard. I dnt know where i can buy 1. Any advice
I WISH I knew if this would solve my drone issues. I am a disabled teacher & biologist. I was bought the AR drone 2.0 to help keep me in good spirit as I no longer had the strength 2 hold a dslr steady. My father set everything up and he had 1 successful flight. The second flight my dad again just wanted 2 do a simple flight and it just dropped out of the air from 5 feet into grass. IT HAS NEVER WORKED SINCE :( We tried the local hobby store where
I purchased got no help only wanting 2 sell new drones. We get a message saying "UNKNOWN ERROR" since 2013 or 14 I think i have tried everything that you tube says 2 check. : No broken crossbars, blades,gears etc. Resetting will get rid of warning then will not get more that 1ft off the ground and then goes where it wants once it even held its altitude.
So any help is gr8t. Don't have $ to waist with all medical care
