Aller au contenu principal

Patching Surfboard Fiberglass

Ce dont vous avez besoin

  1. Patching Surfboard Fiberglass, Patching Surfboard Fiberglass: étape 1, image 1 de 3 Patching Surfboard Fiberglass, Patching Surfboard Fiberglass: étape 1, image 2 de 3 Patching Surfboard Fiberglass, Patching Surfboard Fiberglass: étape 1, image 3 de 3
    • So, to begin, we need a nice clean working area. My place is small so I used my patio set (not the best idea though, as my wife flipped when she found out I was using toxic chemicals where we occasionally eat, just beware.)

    • Things you will need:

    • Surfboard with dings

    • Cleaning tools: wax comb, rag, and Gloves!!!

    • Resin, Q-Cell Filler, Hardener, Fiberglass Cloth

    • Mixing cup, stirring stick,Transparency

    • Sand paper: 1 rough grit and 1 fine grit

    • Starbucks (optional)

  2. Patching Surfboard Fiberglass: étape 2, image 1 de 3 Patching Surfboard Fiberglass: étape 2, image 2 de 3 Patching Surfboard Fiberglass: étape 2, image 3 de 3
    • Next, you need to identify the dinged areas and figure out which method you prefer to use. I used cloth repair on the bigger ones (and the rail ones) and then the sun cure on the small ones (because I have heard it works well enough on small stuff).

  3. Patching Surfboard Fiberglass: étape 3, image 1 de 3 Patching Surfboard Fiberglass: étape 3, image 2 de 3 Patching Surfboard Fiberglass: étape 3, image 3 de 3
    • Now we need to clean the dinged area of all the wax and fiberglass flakes.

    • Grab your comb and scrape any wax from around the area to be repaired.

    • Sand down, approximately 1/4", till you have a nice smooth surface.

    • Cut a small groove (in the direction of the ding) to give the repair mixture somewhere to seep into.

  4. Patching Surfboard Fiberglass: étape 4, image 1 de 3 Patching Surfboard Fiberglass: étape 4, image 2 de 3 Patching Surfboard Fiberglass: étape 4, image 3 de 3
    • Now we come to the mixing process.

    • First figure how much resin you are going to need to adequately cover the cloth piece with a little to spare to pre-dab the dinged area.

    • Add Filler, it helps to make the solution less watery and more workable

    • Then add the hardener; you only need a little and it really depends on the temp. Your box should say what is appropriate for your particular weather.

  5. Patching Surfboard Fiberglass: étape 5, image 1 de 2 Patching Surfboard Fiberglass: étape 5, image 2 de 2
    • Mixing Process (Continued)

    • Put the fiberglass cloth that you cut into the mixture.

    • Stir the cloth in slowly to cover the cloth with mixture without causing air bubbles.

  6. Patching Surfboard Fiberglass: étape 6, image 1 de 3 Patching Surfboard Fiberglass: étape 6, image 2 de 3 Patching Surfboard Fiberglass: étape 6, image 3 de 3
    • Application Process:

    • Pre-dab the area with some of the solution, if there is a chunk of the fiberglass gone, use the solution generously to fill void.

    • Spread the soaked fiberglass cloth over the dinged area and smooth it out with your fingers.

    • Use the transparency to spread the cloth evenly, working out any noticeable bubbles.

  7. Patching Surfboard Fiberglass: étape 7, image 1 de 2 Patching Surfboard Fiberglass: étape 7, image 2 de 2
    • Application Process (Continued)

    • Hold the transparency in place (be aware that it will not stay put).

    • Use tape (scotch, masking, painters) to secure the edges and make sure the transparency is held down tight

    • Curing and Finishup:

    • Let the mixture cure.

    • It should take, depending on your weather, about 1 hour or so to dry completely.

    • Don't remove the transparency until dry.

    • Once dry, remove the transparency and use a fine sand paper to even out any new bumps from the new fiberglass surface.

    • Then, voila! your board should be back to working order. Get out there and this time try to be more careful on the trip back to the car. ;)

Conclusion

To reassemble your device, follow these instructions in reverse order.

3 autres ont terminé cette réparation.

Eric Doster

Membre depuis le 11/10/10

4 384 Réputation

2 tutoriels rédigés

Un commentaire

You forgot step 0 - choose a well-ventilated area (like the outdoors) before opening those aromatic chemical bottles.

Bote Man - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 4

7 derniers jours : 15

30 derniers jours : 49

Total : 28,664