Menu 

Vos paramètres

Mon établi

Accédez rapidement aux tutoriels, aux pièces et aux réponses correspondant à vos appareils
Mon panier (US Store)

On dirait que votre panier est vide

Parcourez notre boutique

Philips DC320 37 Speaker Replacement

Rédigé par : Graham Rolph (et 6 autres contributeurs)
  • Commentaires : 0
  • Favoris : 0

Difficulté

Facile

Étapes

8

Temps nécessaire

20 minutes

Sections

2

Drapeaux

1

Confusing Text

Texte bizarre

Certaines parties de ce texte sont confuses, répétitives ou hors-sujet. Modifie-les pour les rendre plus claires !

Introduction

Follow the procedure outlined in this guide to remove and install a speaker.

Outils

Acheter ces outils

Pièces

Aucune pièce nécessaire.

  1. Pry off the four white feet with the pointed end of the spudger

    • Pry off the four white feet with the pointed end of the spudger

    Traduire

  2. Unscrew the four 15.5 mm Phillips #2 screws that hold the bottom panel to the dock.

    • Unscrew the four 15.5 mm Phillips #2 screws that hold the bottom panel to the dock.

    Traduire

  3. Use the flat end of the spudger to pry the lid off from the two connectors holding it to the body of the dock.

    • Use the flat end of the spudger to pry the lid off from the two connectors holding it to the body of the dock.

    • The connectors on the panel are fragile and may break.

    Traduire

  4. %Livraison gratuite pour toute commande supérieure à 100 $US ou contenant un Pro Tech Toolkit !

    Parcourez notre boutique

  5. Carefully pull up and out the four electrical connectors and the two ribbon connectors connecting the bottom panel and the dock. Electrical Connectors Ribbon Connectors

    • Carefully pull up and out the four electrical connectors and the two ribbon connectors connecting the bottom panel and the dock.

    • Electrical Connectors

    • Ribbon Connectors

    • The cables do not have a lot of slack in them. Be careful not to break the connectors.

    • One wire is soldered onto the bottom panel. Be careful not to break this bond.

    Traduire

  6. Unscrew the two 6 mm Phillips #00 screws attaching the back panel to device.

    • Unscrew the two 6 mm Phillips #00 screws attaching the back panel to device.

    Traduire

  7. Slide the back panel towards top of the device and lift away from the device to detach back panel. Slide the back panel towards top of the device and lift away from the device to detach back panel. Slide the back panel towards top of the device and lift away from the device to detach back panel.

    • Slide the back panel towards top of the device and lift away from the device to detach back panel.

    Traduire

  8. Unscrew the four 16 mm Phillips #2 screws attaching the speaker unit to device.

    • Unscrew the four 16 mm Phillips #2 screws attaching the speaker unit to device.

    Traduire

  9. Slide the speaker towards the bottom of the device to remove. Slide the speaker towards the bottom of the device to remove.

    • Slide the speaker towards the bottom of the device to remove.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 6 autres contributeurs

Graham Rolph

Membre depuis le 18/04/2013

1 Réputation

2 tutoriels rédigés

Badges: 2

Équipe

Cal Poly, Team 3-48, Amido Spring 2013 Membre de l'équipe Cal Poly, Team 3-48, Amido Spring 2013

CPSU-AMIDO-S13S3G48

4 membres

6 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 5

Total : 610