Introduction

This guide will walk you through step-by-step on how to properly remove and install the optical drive in the PlayStation 2 Slimline.

    • Turn off the PlayStation 2 (or PS2) and carefully unplug from the power source. Check to see there are no discs inside the console before flipping the game system upside-down.

    Ajouter un commentaire

  1. Locate the six feet on the bottom of the PS2.
    • Locate the six feet on the bottom of the PS2.

    • Five of the feet are in plain sight and one of the feet is located under the black void sticker on the bottom of the device.

    • IMPORTANT: Removing the black VOID sticker will void the warranty of this device. Proceed at your own risk

    • Some versions of the console, such as the PAL Version, may not have this sticker. In this case, the foot or even the screw should be in plain sight.

    Ajouter un commentaire

    • Use a spudger, flathead screwdriver, or fingernail to pry the five visible feet from the bottom of the device.

    Ajouter un commentaire

    • The sixth foot is located under the black VOID sticker. Remove the sticker before removing the foot underneath.

    Ajouter un commentaire

    • After all of the feet have been removed, locate the six 4.0mm screws on the base of the PS2.

    Ajouter un commentaire

  2. Répandez la magie de Noël
    Obtenez 12 $ de réduction sur les commandes de 50 $ ou plus avec le code FIXMAS12
    Répandez la magie de Noël
    Obtenez 12 $ de réduction sur les commandes de 50 $ ou plus avec le code FIXMAS12
    • Use a #1 Phillips screwdriver to unscrew all six 4.0mm screws from the base of the PS2.

    Ajouter un commentaire

    • Once all of the screws have been removed, pull apart the top plastic cover from the bottom plastic cover. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate. It will take force to pull apart the two halves.

    Ajouter un commentaire

    • If done correctly, you should have a fully detached plastic backing, revealing the electronic components of the PlayStation 2.

    Ajouter un commentaire

    • Locate the optical drive on the motherboard.

    Ajouter un commentaire

    • Unscrew the four 4.0mm screws that mount the optical drive to the motherboard.

    Ajouter un commentaire

    • Locate the three ribbons that are attached to the motherboard.

    • Note: These ribbons are different sizes: one large, one medium and one small sized ribbon.

    Ajouter un commentaire

    • With tweezers, gently detach all three ribbons from the motherboard terminal. Unlock the middle orange ribbon by using tweezers to lift the black tab up on either side.

    • IMPORTANT: The orange ribbon is glued to the metal chassis. Gently pull the ribbon upward to make sure that you don't rip it.

    Ajouter un commentaire

    • Gently lift the optical drive away from the motherboard.

    Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

8 autre(s) ont terminé cette réparation.

Jared Hirata

Membre depuis le 09/04/2013

480 Réputation

7 tutoriels rédigés

Équipe

Cal Poly, Team 17-4, Regan Spring 2013 Membre de l'équipe Cal Poly, Team 17-4, Regan Spring 2013

CPSU-REGAN-S13S17G4

3 membres

7 tutoriels rédigés

I think that if the entire disc drive, assembled with a simple click in connection, would be much easier and faster.

Fernando Salazar - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 6

30 derniers jours : 32

Total : 4,293