Aller au contenu principal

Introduction

The battery is an integral part of the PlayStation Move controller. This guide will help you to remove and replace it with ease.

  1. Turn the controller over and unscrew the four 10mm screws with a PH #00 screwdriver. Turn the controller over and unscrew the four 10mm screws with a PH #00 screwdriver.
    • Turn the controller over and unscrew the four 10mm screws with a PH #00 screwdriver.

  2. Pinch the sides of the back panel to remove it and set it aside. Pinch the sides of the back panel to remove it and set it aside. Pinch the sides of the back panel to remove it and set it aside.
    • Pinch the sides of the back panel to remove it and set it aside.

  3. Hold the base of the controller with one hand and with the other carefully pull up on the white spherical piece to remove it. Hold the base of the controller with one hand and with the other carefully pull up on the white spherical piece to remove it.
    • Hold the base of the controller with one hand and with the other carefully pull up on the white spherical piece to remove it.

  4. Push the Lithium Ion battery from its slot to remove it. Be mindful not to damage the wires or wired components, as the battery will still be attached via its connector.
    • Push the Lithium Ion battery from its slot to remove it.

    • Be mindful not to damage the wires or wired components, as the battery will still be attached via its connector.

  5. Batteries pour ordinateurs portables

    Une réparation facile pour un gain en puissance max.

    Acheter maintenant

    Batteries pour ordinateurs portables

    Une réparation facile pour un gain en puissance max.

    Acheter maintenant
  6. Unscrew the 9mm screw in the battery slot with a PH #00 screwdriver.
    • Unscrew the 9mm screw in the battery slot with a PH #00 screwdriver.

  7. Using a plastic opening tool, carefully pry the rumble motor free. Using a plastic opening tool, carefully pry the rumble motor free.
    • Using a plastic opening tool, carefully pry the rumble motor free.

  8. Unscrew the 9mm screw behind the rumble motor slot with a PH #00 screwdriver.
    • Unscrew the 9mm screw behind the rumble motor slot with a PH #00 screwdriver.

  9. Carefully pinch the plastic sides of the battery slot and lift it (along with the circuit board) from the plastic shell of the move controller. Carefully pinch the plastic sides of the battery slot and lift it (along with the circuit board) from the plastic shell of the move controller. Carefully pinch the plastic sides of the battery slot and lift it (along with the circuit board) from the plastic shell of the move controller.
    • Carefully pinch the plastic sides of the battery slot and lift it (along with the circuit board) from the plastic shell of the move controller.

  10. Using your fingers, carefully pry the square green piece beneath the battery slot free. It is attached via white ribbons which need to be kept intact.
    • Using your fingers, carefully pry the square green piece beneath the battery slot free.

    • It is attached via white ribbons which need to be kept intact.

  11. Follow the white ribbon attached to the part you just removed to a smaller, more rectangular piece. Lift the rectangular piece from its slot to free it. Lift the rectangular piece from its slot to free it.
    • Follow the white ribbon attached to the part you just removed to a smaller, more rectangular piece.

    • Lift the rectangular piece from its slot to free it.

  12. Carefully lift the entire circuit board from the black plastic encasing it. Take extra care not to damage any of the wired components. Take extra care not to damage any of the wired components.
    • Carefully lift the entire circuit board from the black plastic encasing it.

    • Take extra care not to damage any of the wired components.

  13. Using tweezers, carefully pull the power cable from its port on the circuit board. Using tweezers, carefully pull the power cable from its port on the circuit board.
    • Using tweezers, carefully pull the power cable from its port on the circuit board.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Sarah Shand

Membre depuis le 20/02/2017

1 094 Réputation

7 tutoriels rédigés

Équipe

USF Tampa, Team S3-G1, Sullivan Spring 2017 Membre de l'équipe USF Tampa, Team S3-G1, Sullivan Spring 2017

USFT-SULLIVAN-S17S3G1

3 membres

7 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 4

7 derniers jours : 37

30 derniers jours : 143

Total : 1,016