Introduction

This guide takes you through the process of installing the right joystick on the PlayStation Vita.

Power off and remove the memory card.
  • Power off and remove the memory card.

  • Using a Phillips #00 screwdriver, remove the four 6.4mm screws on the back casing.

Ajouter un commentaire

Using your fingernail or a spudger, pry open the accessory port cover on the top of the device.
  • Using your fingernail or a spudger, pry open the accessory port cover on the top of the device.

  • Using a Phillips #00 screwdriver, remove the two 5.4mm screws hidden beneath the accessory port cover.

Ajouter un commentaire

  • Remove the two 5.4mm Phillips #00 screws on the bottom of the device near the charging port.

Ajouter un commentaire

  • Beginning at the sides of the device, use a plastic opening tool to separate the front and rear cases.

  • Continue working your way around the device gently prying it open.

  • There are still wires holding the front and rear cases together. You may damage the connections if you yank the cases completely apart.

Ajouter un commentaire

  • Gently separate the two cases, minding the battery and the touch screen controller connectors holding the two cases together.

Ajouter un commentaire

  • Using a spudger, free the touch screen controller flex cable by gently prying up the connection.

Ajouter un commentaire

  • Free the battery cable by gently prying up on the connection with a spudger.

Any idea what type of pcb header is on the board for the battery? I have a motherboard with a broken header but I cant source a replacement

Jimbo Jones - Réponse

This is where I screwed up so I recommend extra caution for other newbies. Only the black part is supposed to come off. Don't be an idiot like me and pry off too much...

ylimakiminna - Réponse

Yea I messed up there too. Is there a way to fix it?

Alethia Henry - Réponse

  • Separate the front and rear cases.

Ajouter un commentaire

  • Using the pointy end of the spudger, disconnect the three antenna cable connectors on top of the wireless card.

  • Deroute the antenna cables so that they are out of the wireless card casing. Rest the wires out of the way.

Step 9-11 only apply to the 3G version of the PS Vita.

logicj83 - Réponse

Hello, I have the PCH-2001 model of the PS vita and the right analog stick went out. I ordered a replacement and the stick is slightly larger than the original. The original has a black rectangle on the back, the new version has the star version, which is what you have on this website as the replacement part. Any help here would be much appreciated. Thanks.

Ben Ragains - Réponse

  • Hook the spudger beneath the tab on the wireless card casing and release the tab.

  • Peel up and remove the wireless card casing.

Ajouter un commentaire

  • Remove the two 4.4mm Phillips #00 screws on the wireless card.

  • The wireless card will naturally pop out at an angle.

  • Pull out the wireless card.

Ajouter un commentaire

  • Pry up the right shoulder button casing with a spudger and set it aside.

Ajouter un commentaire

  • Remove the translucent, plastic right shoulder button cover.

Ajouter un commentaire

  • Release the right shoulder button flex cable socket by using a spudger to gently pry open the tab.

  • Using tweezers, slide the flex cable out of the socket.

Ajouter un commentaire

  • Using a spudger, gently peel up the right shoulder button from the light adhesive connecting it to casing.

Ajouter un commentaire

  • Using the pointy end of a spudger, detach the antenna cable on the right button board.

  • Remove the antenna cable.

Ajouter un commentaire

  • Using a spudger, pry up and release the ZIF socket on the right button board.

  • Gently pull the flex cable out of the socket. Rest the flex cable out of the way.

Ajouter un commentaire

  • Release the tab on the small flex cable socket by prying up the tab with a spudger.

  • Using tweezers, gently pull the flex cable out of the socket. Rest the flex cable out of the way.

Ajouter un commentaire

  • Remove the two 5.0mm Phillips #00 screws from the metal bracket securing the right button board to the motherboard.

  • Remove the metal bracket, using a spudger as necessary to lift it out.

Ajouter un commentaire

  • Use a spudger to free the right button board by prying up from the bottom right corner of board.

  • Gently lift the right button board out.

Ajouter un commentaire

  • Using a Phillips #00 screwdriver, remove the two 5.0mm, blue screws from the right joystick.

Ajouter un commentaire

  • Using a spudger, gently pry the joystick out of the back casing assembly.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

22 autre(s) ont terminé cette réparation.

Brittany McCrigler

Membre depuis le 05/03/2012

79 187 Réputation

134 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Community

107 membres

6 510 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 4

7 derniers jours : 32

30 derniers jours : 149

Total : 20,216