Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer so that the ports are facing you.
-
If the keyboard is locked, open the port cover and turn the keyboard locking screw until the keyboard is unlocked.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the keyboard out by pulling it up and away from you. Rest the keyboard, face down, on top of the trackpad.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three silver Phillips screws that attach the heat shield to the internal metal framework.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Your laptop should look approximately like this.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the battery cable directly up from the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the battery from its holder by pulling up and to the left.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two silver Phillips screws from the modem.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger, the tips of your fingers, or a flat non-metal tool to get under the modem's edge and pry it up from its socket as shown in the picture.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the cable from the right side of the modem.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Your laptop should look approximately like this.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger, the tips of your fingers, or a flat non-metal tool to pry up the processor's right side.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the keyboard cable from the logic board by pulling directly up on the clear plastic loop.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Your laptop should look approximately like this.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to "pop" up.
-
Pull the RAM chip out.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the orange cable at the left end of the hard drive and disconnect it from the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the plastic tab and pull the hard drive up and to the left, making sure that the metal bracket doesn't catch on the black plastic casing.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Slip a spudger or your index finger under the clutch cover near the power button and pull gently upward until you feel it come free.
-
Repeat the previous step on the left side.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the clutch cover up and off, rotating it toward yourself.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the orange display data cable and disconnect it from the logic board.
-
Pull the display cable straight up so that it is vertical.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the thin display inverter board at its left end, push the left end forward to get the board beyond the tab, and then lift the entire board up.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the white inverter cable connector from the right end of the board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the inverter plug, pulling directly up from the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Your laptop should look approximately like this.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the laptop around so that its back faces you.
-
Open the port door located at the back of the laptop.
-
Remove the four black Torx screws.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Hold the display on both sides and pull directly up until its hinges are free of their mounts.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Your laptop should look approximately like this.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three long silver and two short black Torx screws from the beige plastic casing.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the Lombard so that the trackpad is nearest you and slide the thin plastic shield away from you, out from under the black casing.
-
Disconnect the newly revealed thin orange ribbon from the logic board, to the left of the trackpad.
-
Remove the two long silver Torx screws.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the laptop over.
-
Remove the seven Torx screws from the bottom casing.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the laptop back over.
-
Remove the three short black Torx screws from the metal frame.
-
Remove the short black Torx screw to the far left that fastens the logic board to the casing.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the upper plastic casing where it locks into the internal frame and pull back. When the plastic tab has cleared the slot that the casing locks into, pull up enough to keep it from locking back into place.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
The PC card eject button on the laptop's left side prevents the upper casing from lifting up. In order to bypass the button, push it in far enough so that you can pull the upper casing's left side out and up beyond the button.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the left side of the case partly up so that you can access and disconnect the audio in/out cables from the sound card in the upper right of the case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the upper casing. Note that there are two tabs on the laptop's front that often cause the upper case to stick.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Your laptop should look approximately like this.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two long silver Torx screws from the power card in the center of the laptop.
-
Grasp the power card near the black plastic shield and lift up.
-
Annulation : je n'ai pas terminé ce tutoriel.
2 autres ont terminé cette réparation.