Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a coin to turn the battery locking screw 90 degrees clockwise.
-
Lift the battery out of the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four Phillips screws from the memory door.
-
Slide the memory door away from the memory compartment.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 8 screws:
-
Two 3 mm Phillips in the battery compartment, on either side of the battery contacts.
-
Two 9 mm Phillips on either side of the memory compartment.
-
Four 16 mm Phillips along the hinge.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Rotate the computer 90 degrees clockwise, so that the power receptacle faces you.
-
Remove the three 3 mm Phillips screws.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer 90 degrees clockwise so that the hinge faces you.
-
Remove the bottom 5 mm Phillips screw on either side of the hinge (two total).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Rotate the computer 90 degrees clockwise, so that the ports face you.
-
Remove the three 3 mm Phillips screws.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer over and open the display.
-
Remove the 4.2 mm 1/16" H 1.5 hex screws in either corner, next to the display (a T6 Torx driver will also do the job nicely).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the back corners of the upper case and pull up, disengaging hidden tabs on the sides. Do not pull the upper case off yet; you still need to free tabs in the front of the case.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pry up the left side of the upper case slightly with your hand and wedge a spudger into the seam between the upper case and lower case.
-
Leave the tool in place applying pressure to the upper case for the next step.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Place enough pressure on the upper case to allow you to slide a tool just within the seam between upper case and lower case as shown in the picture. A dentist's hook, push pin, or similar tool will work.
-
Delicately slip the tip of your tool behind the silver metal latch and pull it forward while pulling up on the case. This may take some effort.
-
Alternatively, you can free the clasp with a small flathead screwdriver through the CD slot. The clasp is 1-3/16 in (3cm) from the left side of the slot. Use the screwdriver to lift out (or press back) the felt lining; then use the screwdriver to pull the clasp (shiny metal) forward to free it from the catch behind it (dull metal).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the back of the case up and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case.
-
Rotate the upper case up and toward the screen, so that the upper case rests against it.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the orange tape securing the trackpad ribbon to the logic board.
-
Disconnect the trackpad ribbon from the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
1) With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).
-
2) After disengaging the locking bar, slide the cable out of the connector.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Loosen the keyboard ribbon clamp by pushing the thin black piece toward the screen, using the tips of your fingers.
-
Slide the grey keyboard ribbon out of the loosened connector.
-
Remove the upper case from the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two 6 mm long silver Phillips screws from the metal bracket to the right of the hard drive, removing tape as necessary.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to lift the metal bracket out of the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the large orange hard drive cable from the logic board, removing tape as necessary.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Deroute the red and black speaker cable from under the fold in the hard drive ribbon.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the hard drive up from the right side and remove it from the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Your laptop should look approximately like this.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two black Phillips screws from the modem board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the modem up from the left side and use a spudger to disconnect the cable attached to the bottom.
-
Annulation : je n'ai pas terminé ce tutoriel.
Une autre personne a terminé cette réparation.