Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a coin or a spudger to turn the battery locking screw 90 degrees clockwise.
-
Lift the battery out of the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four Phillips screws from the memory door.
-
Slide the memory door away from the memory compartment.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 8 screws:
-
Two 3 mm Phillips in the battery compartment, on either side of the battery contacts.
-
Two 12 mm Phillips on either side of the memory compartment.
-
Four 16 mm Phillips along the hinge.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Rotate the computer 90 degrees clockwise, so that the power receptacle faces you.
-
Remove the three 3 mm Phillips screws.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer 90 degrees clockwise so that the hinge faces you.
-
Remove the bottom 5 mm Phillips screw on either side of the hinge (two total).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Rotate the computer 90 degrees clockwise, so that the ports face you.
-
Remove the three 3 mm Phillips screws.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer over and open the display.
-
Remove the two 1.5 mm hex screws in either corner, next to the display (a T6 Torx driver will work, but repeated use will strip the screws).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the back corners of the upper case and pull up. Do not pull the upper case off yet; you still need to disconnect the keyboard and trackpad cable.
-
Lift the back of the case up and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Rotate the upper case up and toward the screen, so that the upper case rests against it.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the orange tape securing the trackpad ribbon to the logic board.
-
Disconnect the trackpad ribbon from the logic board.
-
Remove the upper case from the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the 9.5 mm silver Phillips screw from the top of the right ambient light sensor board.
-
Remove the small 3 mm black Phillips screw from the bottom of the board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the right ambient light sensor board Straight up from the Logic Board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two black Phillips screws from the right speaker.
-
Lift the speaker away from the logic board and place it aside
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use your fingernail to flip up the black plastic flap locking the modem cable in place.
-
Slide the modem cable from its connector.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the 13 indicated cables, removing tape as necessary.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 8 Phillips screws from the logic board:
-
Three 6.5 mm in the upper left corner.
-
Five 4.5 mm around the edges.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to gently (very gently) pry up the left side of the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the DC-In connector from the left side of the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the battery cable from the front, left corner of the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the logic board at the left edge with one hand and at the thinnest section with the other hand. Lift the left edge of the board up to approximately a 30 degree angle (if you don't have your protractor handy, just lift until the DVI port clears the right hinge).
-
Once the logic board clears the ports, slide it out to the left.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
To properly reassemble your PowerBook, you'll have to clean off and replace the old thermal compound. Use our Applying Thermal Paste Guide to prepare the processor and heat sink surfaces.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a firm plastic edge to scrape the thermal material off the processor.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two 3 mm black Phillips screws from the left ambient light sensor board.
-
Lift the left ambient light sensor board out of the computer, removing tape as necessary.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Deroute the Bluetooth and RJ-11 cables from around the left side of the speaker.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the speaker cable from the DC/Sound card.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the 4 mm hex nut from below the left speaker.
-
Remove the 3 mm black Phillips screw from bottom left corner of the speaker assembly, to the left of the battery compartment.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the speaker assembly (including the right speaker) out of the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two 4.2 mm silver Phillips screws from the left corners of the PC card cage.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the PC card cage up and remove it from the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two 4.2 mm silver Phillips screws from either side of the large orange Airport ribbon.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the Airport card out of the computer and slide a spudger between the card and the antenna connector to disconnect the cable from the card.
-
Deroute the antenna cable from the side of the card, removing tape as necessary.
-
You don't need to remove the Airport card entirely. We're just trying to free up the Airport antenna cable.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using a spudger, pry up the Bluetooth board from the cavity in front of the battery compartment.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the Bluetooth antenna cable from the Bluetooth board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Close the display and turn the hinge side of the computer to face you.
-
Remove the remaining Phillips screw on either side of the hinge (two screws total).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Open the display and turn the computer so the screen faces you.
-
Remove the 10 mm T8 Torx screw closer to the display on either side of the hinge (two screws total).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the longer 13 mm shouldered T8 Torx screw remaining on either hinge (two screws total).
-
Annulation : je n'ai pas terminé ce tutoriel.
14 autres ont terminé cette réparation.