Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use your thumbs to push the two battery retaining tabs away from the battery.
-
The battery should pop up enough to rotate it toward yourself and lift it out of the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three 2.3 mm Phillips screws securing the memory cover to the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the memory cover slightly and pull it toward yourself to remove it from the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following ten screws:
-
Two 14.7 mm shouldered Phillips.
-
Three 12.3 mm Phillips.
-
One 3.8 mm T8 Torx.
-
One 6.8 mm T8 Torx.
-
Three 1.3 mm Phillips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use your fingernails to separate the ZIF cable lock away from its socket. (Move the two brown bits down 1mm)
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the tip of a spudger to slide the trackpad ribbon cable out of its socket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four 3.4 mm Phillips screws from the PC card side of the PowerBook.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four 3.4 mm Phillips screws from the DVI connector side of the PowerBook.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Depress the display latch release button and open your display.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Starting near the display, lift the upper case straight up off the lower case, minding any cables that may get caught.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger to pry the sound card ribbon cable connector up off the logic board.
-
Move the sound card ribbon cable away from the face of the hard drive.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger to pry the hard drive ribbon cable connector up off the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following four screws:
-
Three 11.1 mm T8 Torx.
-
One 3.9 mm T8 Torx.
-
Lift the hard drive out of the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
If necessary, remove the strip of tape covering the speaker cable.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the speaker cable connector straight up to disconnect it from the sound card.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two T8 Torx screws securing the sound card to the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger to pry the USB sockets away from the left edge of the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the sound card slightly out of the lower case, minding the fragile lower portion holding the microphone connector.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the sound card ribbon cable straight away from its socket on the sound card.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use your fingernails to pull the microphone connector straight away from its socket on the sound card.
-
Annulation : je n'ai pas terminé ce tutoriel.
3 autres ont terminé cette réparation.