Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use your thumbs to push the two battery retaining tabs away from the battery.
-
The battery should pop up enough to rotate it toward yourself and lift it out of the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three 2.3 mm Phillips screws securing the memory cover to the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the memory cover slightly and pull it toward yourself to remove it from the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following ten screws:
-
Two 14.7 mm shouldered Phillips.
-
Three 12.3 mm Phillips.
-
One 3.8 mm T8 Torx.
-
One 6.8 mm T8 Torx.
-
Three 1.3 mm Phillips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use your fingernails to separate the ZIF cable lock away from its socket. (Move the two brown bits down 1mm)
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the tip of a spudger to slide the trackpad ribbon cable out of its socket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four 3.4 mm Phillips screws from the PC card side of the PowerBook.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four 3.4 mm Phillips screws from the DVI connector side of the PowerBook.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Depress the display latch release button and open your display.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Starting near the display, lift the upper case straight up off the lower case, minding any cables that may get caught.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
If necessary, remove the strip of tape covering the speaker cables.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use your fingernails or the tip of a spudger to separate the ZIF cable lock from its socket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the DC-in ribbon cable straight away from its socket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Peel the DC-in cable off the adhesive securing it to the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
If necessary, use the tip of a spudger to remove the small piece of foam tape from the side of the left speaker.
-
De-route the AirPort antenna cables from the channel in the left speaker.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single 6.9 mm T8 Torx screw securing the left speaker to the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the left speaker from its rear edge and maneuver it out of the lower case, minding the cables sitting in the channel near the front edge of the left speaker.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single 6.9 mm T8 Torx screw securing the speaker cable ground loop to the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Peel back the piece of foil tape covering the modem cable to free the speaker cable held underneath.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the speaker cable straight up to disconnect it from the sound card.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger to pry the hard drive ribbon cable connector up off the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger to pry the sound card cable connector up off the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger to pry the optical drive cable connector up off the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use your fingernails or the tip of a spudger to separate the ZIF cable lock from its socket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the PRAM battery & USB board cable out of its socket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to de-route the display data cable from the channel in the right speaker.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the tip of a spudger to pry the power button LED window off the right speaker.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single T8 6.9 mm Torx screw securing the right speaker to the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
De-route the speaker cable from the clips along the front edge of the logic board.
-
Annulation : je n'ai pas terminé ce tutoriel.
2 autres ont terminé cette réparation.