Introduction

If the motherboard becomes damaged, all other electronics must be removed first before you can access it. This guide will show you the steps necessary to access the motherboard.

Pièces

Aucune pièce nécessaire.

Remove the strap by pulling it off of the mounts located on the body and neck. Remove the strap by pulling it off of the mounts located on the body and neck.
  • Remove the strap by pulling it off of the mounts located on the body and neck.

Ajouter un commentaire

Remove the nine 12mm Phillips #1 screws around the perimeter of the case with a  screwdriver. Remove the two 15mm Phillips #1 screws connecting the body panel to the neck panel with a screwdriver. Pull off the rear case.
  • Remove the nine 12mm Phillips #1 screws around the perimeter of the case with a screwdriver.

  • Remove the two 15mm Phillips #1 screws connecting the body panel to the neck panel with a screwdriver.

  • Pull off the rear case.

Ajouter un commentaire

Remove the five 12mm Phillips #1 screws along the neck with a  screwdriver. Pull off the top shell of the neck to expose the internal features. Pull off the top shell of the neck to expose the internal features.
  • Remove the five 12mm Phillips #1 screws along the neck with a screwdriver.

  • Pull off the top shell of the neck to expose the internal features.

Ajouter un commentaire

Remove the two 10mm Phillips #1 screws from the auxiliary port board using a  screwdriver. Gently lift up on the auxiliary port to remove it from the case. Gently lift up on the auxiliary port to remove it from the case.
  • Remove the two 10mm Phillips #1 screws from the auxiliary port board using a screwdriver.

  • Gently lift up on the auxiliary port to remove it from the case.

Ajouter un commentaire

Remove the two 10mm Phillips #1 screws from the Ethernet connector board. Lift the Ethernet connector to remove it from the case. Lift the Ethernet connector to remove it from the case.
  • Remove the two 10mm Phillips #1 screws from the Ethernet connector board.

  • Lift the Ethernet connector to remove it from the case.

Ajouter un commentaire

Use a screwdriver to remove the 10 mm Phillips #1 screws from the key sensor board. Lift up on the key sensor board to remove it from the guitar neck. When using the screwdriver, make sure to avoid puncturing the wires.
  • Use a screwdriver to remove the 10 mm Phillips #1 screws from the key sensor board.

  • Lift up on the key sensor board to remove it from the guitar neck.

  • When using the screwdriver, make sure to avoid puncturing the wires.

Ajouter un commentaire

Using your fingers, remove the rubber pad to expose the colored keys.
  • Using your fingers, remove the rubber pad to expose the colored keys.

Ajouter un commentaire

Reach one finger under the guitar to push the key out of the casing. Repeat this step for the four remaining keys.
  • Reach one finger under the guitar to push the key out of the casing.

  • Repeat this step for the four remaining keys.

Ajouter un commentaire

Use a screwdriver to remove the four 14mm Phillips #1 screws  around the perimeter of the strum bar sensor board. Lift up on the strum bar sensor board to remove it from the case. Lift up on the strum bar sensor board to remove it from the case.
  • Use a screwdriver to remove the four 14mm Phillips #1 screws around the perimeter of the strum bar sensor board.

  • Lift up on the strum bar sensor board to remove it from the case.

Ajouter un commentaire

Remove the two 7mm Phillips #0 screws. Using your fingers, remove the black wire retainer. Using your fingers, remove the black wire retainer.
  • Remove the two 7mm Phillips #0 screws.

  • Using your fingers, remove the black wire retainer.

Ajouter un commentaire

Using one hand, remove the whammy bar and its attached components from the case. Using one hand, remove the whammy bar and its attached components from the case.
  • Using one hand, remove the whammy bar and its attached components from the case.

Ajouter un commentaire

Using two hands, remove the whammy bar sensor.
  • Using two hands, remove the whammy bar sensor.

Ajouter un commentaire

Remove the four 10mm Phillips #1 screws  around the perimeter of the motherboard with a screwdriver. Lift the motherboard to remove it from the case. Lift the motherboard to remove it from the case.
  • Remove the four 10mm Phillips #1 screws around the perimeter of the motherboard with a screwdriver.

  • Lift the motherboard to remove it from the case.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Riley

Membre depuis le 18/04/2018

565 Réputation

7 tutoriels rédigés

Équipe

Cal Poly, Team S17-G1, Livingston Spring 2018 Membre de l'équipe Cal Poly, Team S17-G1, Livingston Spring 2018

CPSU-LIVINGSTON-S18S17G1

4 membres

10 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 3

30 derniers jours : 25

Total : 61