Aller au contenu principal

Pièces

Aucune pièce spécifiée.

  1. Turn over the Delphi MyFi XM2GO Device on its back to start the cover-removal process.
    • Turn over the Delphi MyFi XM2GO Device on its back to start the cover-removal process.

  2. Locate the large button on the top back of the device. Press this button at the top while making a firm grip on the battery cover. As the button is pressed, move the cover towards the bottom of the device.
    • Locate the large button on the top back of the device.

    • Press this button at the top while making a firm grip on the battery cover.

    • As the button is pressed, move the cover towards the bottom of the device.

    • The battery removal tab may pop up during the cover removal process.

  3. Holding the device, grab the tab with thumb and index figure. Pull down on the tab to move the battery block a few millimeters towards the bottom of the device to unlock the latch at the top. After the latch at the top is disengaged, pivot the battery away from the back and the battery will be free.
    • Holding the device, grab the tab with thumb and index figure.

    • Pull down on the tab to move the battery block a few millimeters towards the bottom of the device to unlock the latch at the top.

    • After the latch at the top is disengaged, pivot the battery away from the back and the battery will be free.

  4. locate the four hex screws on the bottom of the device. Use a T6 hex bit  from the iFixit precision screwdriver set to remove the four screws. Use a T6 hex bit  from the iFixit precision screwdriver set to remove the four screws.
    • locate the four hex screws on the bottom of the device.

    • Use a T6 hex bit from the iFixit precision screwdriver set to remove the four screws.

  5. To remove the next two T6 screws, locate the button at the top of the back of the device. Around the button, there is a cover that protects the two screws. To remove the cover insert a flathead screwdriver or thumb nail and lift up until cover is removed.
    • To remove the next two T6 screws, locate the button at the top of the back of the device.

    • Around the button, there is a cover that protects the two screws.

    • To remove the cover insert a flathead screwdriver or thumb nail and lift up until cover is removed.

  6. After removing the cover, use the T6 screwdriver and remove the screws. After removing the cover, use the T6 screwdriver and remove the screws. After removing the cover, use the T6 screwdriver and remove the screws.
    • After removing the cover, use the T6 screwdriver and remove the screws.

  7. Batteries pour ordinateurs portables

    Une réparation facile pour un gain en puissance max.

    Acheter maintenant

    Batteries pour ordinateurs portables

    Une réparation facile pour un gain en puissance max.

    Acheter maintenant
  8. With the 6 screws removed, the back cover can be removed revealing the backside of the motherboard (PCB Logic Board). Pull up on the back cover from the device. Locate the power button.
    • With the 6 screws removed, the back cover can be removed revealing the backside of the motherboard (PCB Logic Board).

    • Pull up on the back cover from the device.

    • Locate the power button.

  9. Remove the power button from the left. Locate the antenna extension connector on the right and remove the plastic piece. Locate the antenna extension connector on the right and remove the plastic piece.
    • Remove the power button from the left.

    • Locate the antenna extension connector on the right and remove the plastic piece.

  10. After removing the screws and two external pieces, the PCB Logic Board can be removed from the front piece. Simply pull up on the PCB Logic Board to remove. CAUTION: Be careful of the LCD screen and keypad as they are only connected via ribbon cables to the board. They will hang down as the PCB Logic Board is removed.
    • After removing the screws and two external pieces, the PCB Logic Board can be removed from the front piece.

    • Simply pull up on the PCB Logic Board to remove.

    • CAUTION: Be careful of the LCD screen and keypad as they are only connected via ribbon cables to the board. They will hang down as the PCB Logic Board is removed.

  11. The logic board must be exposed to begin. Flip the device over (see second picture).
    • The logic board must be exposed to begin.

    • Flip the device over (see second picture).

    • CAUTION: The keyboard is loosely attached by a ribbon cable and may move when the device is flipped.

  12. Lift up the keyboard carefully from the right side, flipping to the left.
    • Lift up the keyboard carefully from the right side, flipping to the left.

    • NOTE: The keyboard is attached on the left side by a ribbon cable. Do not remove it completely yet.

  13. Pivot the LCD screen, pulling on the top and sides and keeping the bottom attached. Pivot the LCD screen, pulling on the top and sides and keeping the bottom attached. Pivot the LCD screen, pulling on the top and sides and keeping the bottom attached.
    • Pivot the LCD screen, pulling on the top and sides and keeping the bottom attached.

  14. Continue to pivot the screen until it is lying on its face. Pivot the wire frame, that was under the LCD, from the left side. CAUTION: The wire bends as the frame pivots.  Use the least amount of force necessary.
    • Continue to pivot the screen until it is lying on its face.

    • Pivot the wire frame, that was under the LCD, from the left side.

    • CAUTION: The wire bends as the frame pivots. Use the least amount of force necessary.

  15. With the frame perpendicular to the device, locate the two black, plastic tabs shown in the two red circles. The boxes show more detailed views in the following pictures. The boxes show more detailed views in the following pictures.
    • With the frame perpendicular to the device, locate the two black, plastic tabs shown in the two red circles.

    • The boxes show more detailed views in the following pictures.

  16. WIth both hands, pull the tabs outwards to release the plastic cover from the board. Once the tabs are disengaged, pivot the plastic cover upwards. After the cover is pivoted slightly, remove it from the device.
    • WIth both hands, pull the tabs outwards to release the plastic cover from the board.

    • Once the tabs are disengaged, pivot the plastic cover upwards.

    • After the cover is pivoted slightly, remove it from the device.

  17. After the plastic cover is removed, locate the white, ribbon connector highlighted by the red square. Rotate the device 90 degrees counterclockwise to remove the ribbon connector.
    • After the plastic cover is removed, locate the white, ribbon connector highlighted by the red square.

    • Rotate the device 90 degrees counterclockwise to remove the ribbon connector.

  18. To remove the ribbon cable from the board, catch the sides of the connector with fingernails and pull downward. CAUTION: The connector is delicate. After the latch is pulled down, the ribbon cable is free to slide out of the connector housing.
    • To remove the ribbon cable from the board, catch the sides of the connector with fingernails and pull downward.

    • CAUTION: The connector is delicate.

    • After the latch is pulled down, the ribbon cable is free to slide out of the connector housing.

  19. After following the prerequisite steps in the guide, the components are laid out as depicted in the picture.
    • After following the prerequisite steps in the guide, the components are laid out as depicted in the picture.

    • The LCD screen is highlighted in red.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Aubrey

Membre depuis le 09/03/2012

54 Réputation

3 tutoriels rédigés

Équipe

Clemson, Team 1-2, Benson Spring 2012 Membre de l'équipe Clemson, Team 1-2, Benson Spring 2012

CLEM-BENSON-S12S1G2

3 membres

9 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 3

Total : 1,684