Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Introduction
Veillez à éteindre complètement votre Moto X4 avant de sortir votre iOpener pour ouvrir le téléphone.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Heat an iOpener and apply it to the left edge of the phone for two minutes.
-
As you wait, take note of the the following areas:
-
Display cable—be careful not to slice too deeply near the edge here, or you may damage the display cable.
-
Fingerprint sensor cable—be careful not to slice too deeply near the edge here, or you may damage the fingerprint sensor cable.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Apply a suction cup to the screen, as close to the heated edge as possible.
-
Pull on the suction cup with strong, steady force to create a gap in the seam.
-
Insert the point of an opening pick into the gap.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Slide the opening pick along the edge to slice through the adhesive.
-
Leave an opening pick in the seam to prevent the adhesive from re-sealing.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Heat the top edge of the phone with an iOpener.
-
Carefully slice around the corner and through the top edge to separate the adhesive.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Heat the screen's right edge with an iOpener.
-
Be careful not to slice too deeply near the cables to avoid damaging them.
-
Use an opening pick to slice along the right edge to separate the adhesive.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Repeat the previous steps to heat and slice the bottom edge of the phone.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Carefully lift up the left edge of the screen and cut away remaining adhesives with an opening pick.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Swing open the screen and prop it up with a small box as you work on disconnecting the flex cables.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Slide the point of a spudger underneath the fingerprint sensor cable and gently pry up to loosen the cable from the phone.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the point of a spudger to flip up the lock bar on the fingerprint sensor's ZIF socket, near the bottom right of the phone.
-
Use tweezers to carefully slide the fingerprint sensor cable out of the socket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use an opening tool to flip up the wide lock bar on the display cable's ZIF socket, near the top right of the phone.
-
Use tweezers to carefully slide the display cable out of the ZIF socket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Apply a heated iOpener to the fingerprint sensor for one minute to soften the adhesive gasket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Slide the point of a spudger under the fingerprint sensor cable and gently pry to loosen the cable from the screen.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use an opening tool to pry up and loosen the fingerprint sensor from the screen.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat edge of a spudger to push the grille from the front side of the screen to loosen it from its recess.
-
Remove the grille.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
If your replacement part did not come with a lower microphone gasket, use tweezers to carefully peel it from your old screen and transfer it to your replacement part.
-
Pour remonter votre appareil, suivez ces instructions en sens inverse.
Pour remonter votre appareil, suivez ces instructions en sens inverse.
Annulation : je n'ai pas terminé ce tutoriel.
23 autres ont terminé cette réparation.
Merci à ces traducteurs :
0%
Claire Miesch nous aide à réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›
8 commentaires
This guide really only covers screen removal, and should detail replacing the screen as advertised. Here are a few more steps that should be added:
1. Transferring old hardware to the new screen (seals, filters, fingerprint sensor, & the grey carbon mat.
2. Cleaning up old adhesive.
3. Applying new adhesive, whether it’s the one-piece that ifixit carries (recommended), or Tesa tape.
4. Installing the new display assembly
Is it possible to remove and replace only the glass? Can I do that without removing the whole LCD screen and avoid disconnecting/reconnecting wires?
Hi Drew,
I haven’t tried, but I think it is possible to do a glass-only repair for this LCD screen, as long as you have the necessary tools and bonding adhesives. You would still have to deal with the fingerprint sensor, which is sealed onto the glass.
I noticed the fingerprint sensor not being quite as low on the right edge after this. Also, I think it has a bit of “give” now when I press on it with a thumbnail. If the tips of my thumbs weren't so dry right now I might not have noticed, though.
Hey Chris,
Did you add adhesive to the fingerprint sensor, if you didn't add some adhesive it may have some play, as most things need to be glued in place, and you could have forgotten to add some new adhesive.