Introduction
Avec ce tutoriel, remplacez l'écran cassé de votre MacBook Pro Unibody.
Ce dont vous avez besoin
-
-
Boîtier fermé, placez l'Unibody à l'envers sur une surface plane.
-
Appuyez sur le côté rainuré du loquet de déverrouillage de la trappe d'accès de manière à saisir l'extrémité libre du loquet. Soulevez le loquet de déverrouillage à la verticale.
-
-
-
Tirez sur la languette et retirez la batterie de votre MacBook.
-
Si la languette n'est pas bien positionnée, elle empêchera la batterie de sortir.
-
-
-
Retirez les huit vis suivantes par lesquelles le boîtier inférieur est fixé au châssis :
-
Une vis Phillips 5,4 mm.
-
Trois vis Phillips 14 mm.
-
Quatre vis Phillips 3,5 mm.
-
-
-
-
Déconnectez la nappe de la caméra en tirant l'extrémité mâle tout droit hors de sa prise, vers l'ouverture du lecteur optique.
-
Dégagez le câble de données de l'écran de la rainure sur le lecteur optique.
-
-
-
Ouvrez votre MacBook de sorte que l'écran est perpendiculaire au boîtier supérieur.
-
Posez votre MacBook ouvert sur une table comme sur la photo.
-
Pendant que vous maintenez l'écran et le boîtier supérieur d'une main, dévissez la vis Torx de 6 mm restante de la fixation inférieure de l'écran.
-
-
-
Saisissez le boîtier supérieur de votre main droite et faites-le légèrement pivoter vers le haut de l'écran de sorte que la fixation supérieure de l'écran s'éloigne du bord du boîtier supérieur.
-
Faites pivoter et éloignez légèrement l'écran du boîtier supérieur.
-
Soulevez et éloignez l'écran du boîtier supérieur en veillant à ce que aucune fixation ni aucune nappe ne reste accrochée.
-
Pour remonter votre ordinateur, suivez ces instructions en sens inverse.
Pour remonter votre ordinateur, suivez ces instructions en sens inverse.
Annulation : je n'ai pas terminé ce tutoriel.
61 autres ont terminé cette réparation.
Merci à ces traducteurs :
100%
Ces traducteurs nous aident réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›
6 commentaires
I used this guide to replace my hinges, but I noticed that the real problem was that the display was separating from the case. I Googled it and found a few reports like (https://discussions.apple.com/thread/371...) indicating that Apple has a replacement program in place addressing this as a latent defect.
I took my machine to the local Apple store, and even though I bought it at the end of 2008, they replaced the display for free.
If you're having a display separation issue it's worth seeing what Apple says before digging into it.
This thread is now "not authorized" for viewing. I think Apple doesn't want anyone to know about this issue!
This is a great guide. I also read the guide pertaining to the 2.53 GHz Mid-2009 MacBook Pro Display Assembly.
I wanted to report that I successfully removed the display assembly from a Mid-2009 MacBook Pro (2.53 GHz - no discrete graphics) and installed it on the Late-2008 MacBook Pro (2.53 GHz with dual graphics).
Everything appears to be identical, except (strangely) the screws, that are generally captive in the camera cable and the LVDS cable, need to stay with their original MacBook Pro. Meaning, keep all the screws with the same MacBook Pro. The other screws did appear to be identical though.
Bottom line, keep the screws to the same MacBook. That's easy enough, just remove the captive screws from the cables to keep them with the same MacBook Pro they were from.
(Also, the camera cable where it attaches the logic board was slightly closer to the optical drive and seemed to overlap it slightly when transferring the Mid-2009 display to the Late-2008 MacBook Pro. This didn't seem to pose a problem.)
I have to add to my previous comment about switching a mid-2009 15 inch MacBook Pro display to a late 2008 MacBook Pro. The reed switch that causes the computer to sleep when closing the display is on the other side. I tested this by holding a broken display (which has lots of magnets across the top) near the right side and this 2.53 GHz late-2008 Unibody MacBook Pro went to sleep. The magnet for the reed switch on the mid-2009 display is about halfway up the left side of the display. So I didn't notice this until I tried to close the MacBook and the backlight stayed on.
So while the display works perfectly and the hinges, camera cable, and LVDS cable match, the reed switch magnet is on the left side now (that meets the ExpressCard/34 slot, instead of the SD Card slot) instead of on the right (near the security slot) where the actual reed switch is for the late-2008 MacBook Pros.
I can just choose sleep from the Apple Menu every time, or put a tiny "refrigerator" magnet on the right side of the display.
gatortpk -