Introduction
Consultez ce tutoriel pour remplacer l'écran cassé, fissuré ou défectueux de votre Apple Watch Series 2.
Veillez à mettre à jour votre Apple Watch avec le système d'exploitation watchOS 5 ou plus récent (ainsi que l'iPhone jumelé avec iOS 12 ou plus récent) pour éviter d'avoir des problèmes de synchronisation après avoir remplacé l'écran.
Le remplacement de l'écran peut causer des problèmes avec Apple Pay. Si possible, réduisez les risques en supprimant les infos de votre compte Apple Pay avant le remplacement, puis en les ressaisissant une fois le nouvel écran installé.
Ce dont vous avez besoin
Vidéo d'introduction
-
-
Avant de commencer toute réparation, ôtez votre montre de son chargeur et éteignez-la.
-
-
-
Préparez un iOpener (ou servez-vous d'un sèche-cheveux ou d'un pistolet à air chaud) et faites chauffer l'écran pour ramollir l'adhésif qui le fixe.
-
Laissez l'iOpener agir pendant au moins une minute pour chauffer complètement l'écran et ramollir l'adhésif qui le fixe à la coque.
-
-
-
Insérez le bord d'une lame courbée dans le fin interstice entre l'écran et le boîtier extérieur. Commencez du côté court de l'écran, le plus proche de la couronne digitale.
-
Appuyez fermement à la verticale vers le bas dans l'interstice.
-
Une fois qu'elle est dedans, faites pivoter la lame pour soulever légèrement l'écran.
-
-
-
-
Avec un tournevis Y000, dévissez la vis Tri-point qui maintient le cache métallique du connecteur de la batterie.
-
Ôtez le cache.
-
-
-
Prenez une pincette pour décoller l'autocollant qui recouvre les connecteurs des nappes de l'écran.
-
Commencez en bas à droite de la bande et progressez soigneusement vers le connecteur du milieu.
-
Continuez à l'étape 10 de notre tutoriel Force Touch Sensor pour refermer votre Apple Watch et terminer votre réparation. Pour un meilleur résultat, ne connectez pas le nouvel écran avant l'étape 17.
Continuez à l'étape 10 de notre tutoriel Force Touch Sensor pour refermer votre Apple Watch et terminer votre réparation. Pour un meilleur résultat, ne connectez pas le nouvel écran avant l'étape 17.
Annulation : je n'ai pas terminé ce tutoriel.
98 autres ont terminé cette réparation.
Merci à ces traducteurs :
100%
Ces traducteurs nous aident réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›
18 commentaires
Job done….With a smashed screen remember to apply clear scotch tape to hold the screen together. Continue to heat the remaining stuck shards when the main bulk of the glass comes out. Pick them out carefully, and not to raise the gasket. Use a strong magnifying glass. the ifixit heat gel pack and tweezers helped me. Ensure that all tiny bits of glass have been removed form the body. Just turn it upside down, give a couple of gentle taps with something plastic. Pick out if necessary, taking care around the components. For a smashed screen, needs a good hour or more.
Congratulations on the successful repair. And thanks for your comment and additional hints.
This one was tough…and I’ve been doing various repair for years. Thank you iFixIt for top notch tutorials and instructions (and the progressive photos). I had a broken display and an iCloud locked watch for parts. Getting the display off the broken iWatch was easy…getting the replacement/good display off the other iWatch was very difficult. I keep at it and eventually it released, but I think I chipped the display edges slightly. If I have to do this one again, I may think twice. I’d say use plenty of heat. I used the iRemover, which helped a lot, it gets plenty hot and holds the heat for job. Once you’re inside, you’ll need that every so special 000 tri-lobe bit for the battery (for this I bought the iFixIt Pro toolkit…worth it to have a solidly made set of disassembly tools). I don’t think it’s worth breaking down the iWatch for repairs much further than the display or battery. The water resistant seal is compromised enough as it is with the display removal.
Just wondering are the ion x glass and sapphire crystal screens interchangeable because I have a broken series 2 aluminum case and it comes with the ion x glass but I want to get the sapphire crystal glass instead to make it stronger
Displays of the same Series, model and size should be compatible.