Aller au contenu principal

Remplacement de l'écran du Google Pixel 4a

Ce dont vous avez besoin

  1. Remplacement de l'écran du Google Pixel 4a, Avertissements: étape 1, image 1 de 3 Remplacement de l'écran du Google Pixel 4a, Avertissements: étape 1, image 2 de 3 Remplacement de l'écran du Google Pixel 4a, Avertissements: étape 1, image 3 de 3
    • Vous aurez besoin de remonter l'écran vers le haut pour le retirer du reste du téléphone. Suivez les informations suivantes attentivement avant de commencer.

    • Distinguez bien les deux jointures sur le bord du téléphone :

    • Jointure de l'écran : cette jointure sépare l'écran du reste du téléphone. C'est là qu'il faudra faire levier.

    • Jointure du châssis : c'est là que se rejoignent le châssis en plastique et la coque arrière du téléphone. Ne vous appuyez pas sur cette jointure pour faire levier.

    • Avant de démarrer, remarquez les zones suivantes sur l'écran :

    • Nappe de l'écran : n'introduisez pas le médiator plus loin qu'indiqué, vous risqueriez d'endommager cette nappe.

    • Prenez note de la nappe orange sous le coin inférieur droit de l'écran, qui est susceptible de s'abîmer si votre médiator appuie dessus. Insérez votre outil aussi peu que nécessaire pour décoller l'adhésif de l'écran.

    • Périmètre adhésif : faire levier au-delà de ce périmètre étroit sans incliner le médiator endommagera le panneau OLED.

    Coll down guys and gals.

    1) go below the Display and not between the backcover/middle (see the other comments)

    2) just take care about the flex/display cable position (which is iirc about on the middle i.e. 2nd 3rd from the bottom ON THE LEFT side dear OP)

    Everything else is just separting the glued on Display from the Phone.

    See the other comments

    Aleksandar Dejanovic - Réponse

    Cool down guys and gals.

    1) go below the Display and not between the backcover/middle (see the other comments)

    2) just take care about the flex/display cable position (which is iirc about on the middle i.e. 2nd 3rd from the bottom ON THE LEFT side dear OP)

    Everything else is just separting the glued on Display from the Phone.

    See the other comments

    Aleksandar Dejanovic - Réponse

    I've measured it: The cable starts arround 1.4-1.6 cm from the lower half from the bottom on the left side.

    So You can cut the bottom left corner and of course the upper left one but for safety's sake, watch out for the camera.

    You can go up to 5cm down from the upper left side till You're near the cable.

    Aleksandar Dejanovic - Réponse

    When you say left side, is this your left when the phone screen is facing you?

    jaunie -

    The third image her shows the back of the screen, not the body of the phone

    blueslondon - Réponse

  2. Remplacement de l'écran du Google Pixel 4a, Chauffer le bord droit de l'écran: étape 2, image 1 de 1
    • Appliquez un iOpener chaud sur le côté droit du téléphone pendant une minute pour ramollir l'adhésif.

    • Un sèche-cheveux, un pistolet à air chaud ou une plaque chauffante peuvent faire l'affaire, mais faites attention à ne pas surchauffer le téléphone : l'écran et la batterie interne sont tous les deux sensibles à la chaleur et peuvent être endommagés.

  3. Remplacement de l'écran du Google Pixel 4a, Insérer un médiator: étape 3, image 1 de 3 Remplacement de l'écran du Google Pixel 4a, Insérer un médiator: étape 3, image 2 de 3 Remplacement de l'écran du Google Pixel 4a, Insérer un médiator: étape 3, image 3 de 3
    • Si votre écran est méchamment fissuré, couvrez-le avec du scotch transparent pour que la ventouse adhère mieux. Du gros scotch peut être utilisé comme alternative à la ventouse. En dernier recours, vous pouvez coller la ventouse à l'écran cassé avec de la super glue.

    • Positionnez la ventouse aussi près que possible du bord droit de l'écran.

    • Soulevez la ventouse de manière ferme et constante.

    • Insérez la pointe d'un médiator dans la jointure de l'écran sur moins d'un millimètre.

    It's pretty easy. Insert it just below the screen between the Display and the Display “holder” or mold.

    Aleksandar Dejanovic - Réponse

  4. Remplacement de l'écran du Google Pixel 4a, Guider le médiator sous le panneau OLED: étape 4, image 1 de 3 Remplacement de l'écran du Google Pixel 4a, Guider le médiator sous le panneau OLED: étape 4, image 2 de 3 Remplacement de l'écran du Google Pixel 4a, Guider le médiator sous le panneau OLED: étape 4, image 3 de 3
    • Cette étape montre comment insérer le médiator sans abîmer le panneau OLED. Faites cela avant de commencer à découper l'adhésif.

    • Avec votre médiator enfoncé d'un millimètre dans le trou, faites-le pivoter vers le haut pour former un angle raide.

    • Lorsque l'angle est raide, poussez doucement le médiator dans la fente d'environ 6 mm (1/4 pouce). Le médiator devrait se glisser sous le panneau OLED.

    • Arrêtez si vous sentez la pointe du médiator buter sur un obstacle. Le médiator pourrait appuyer sur le bord du panneau OLED. Rehaussez le médiator et réessayez.

    This took me a while, I ended up sharpening the tip of the pick with a razor so I could push it through the seam and slicing a few times, heat->sharpen-> slice until I finally got it to move, and once it slid under carefully heated up areas and sliced with ~2mm of the pick.

    Alan Carlson - Réponse

    This sounds also harder than it is. Push it in 1mm and just lift the other end in a wider angle like 70° degree from the horinzontal position. There “shouldn't” be much you can do wrong. Because except for the Data cable (flex) at a certain position, I can't remeber anything important but isolating tapes that I have scratched.

    It's just the Screen glued to the mold. That's it.

    Aleksandar Dejanovic - Réponse

    Oh, and I wonder here where do You all get such thins plectrums? I have also the flat plastic version and the thin plastic cards but none of them were thin enough for this!!

    I ended up using the backside i.e. the dull side of a Razorblade. I didn't saw any alternatives to this. Did You hear this OP?

    Any!!

    Aleksandar Dejanovic - Réponse

    the display flex is directly on the bottom of the phone. BE VERY CAREFUL when going around the bottom to not hit the display flex!!!

    FixItAgain - Réponse

  5. Remplacement de l'écran du Google Pixel 4a, Couper l'adhésif: étape 5, image 1 de 3 Remplacement de l'écran du Google Pixel 4a, Couper l'adhésif: étape 5, image 2 de 3 Remplacement de l'écran du Google Pixel 4a, Couper l'adhésif: étape 5, image 3 de 3
    • Faites glisser le médiator le long du bord droit de l'écran pour couper l'adhésif.

    • N'insérez pas le médiator de plus de 6 mm (1/4 pouce) au risque d'abîmer la nappe de l'écran.

    • Laissez le médiator en place dans le coin en haut à droite pour empêcher l'adhésif de se recoller.

    The display flex is directly on the bottom of the phone. Be very careful when goign around the bottom to not hit the display flex!!!

    FixItAgain - Réponse

  6. Remplacement de l'écran du Google Pixel 4a: étape 6, image 1 de 3 Remplacement de l'écran du Google Pixel 4a: étape 6, image 2 de 3 Remplacement de l'écran du Google Pixel 4a: étape 6, image 3 de 3
    • L'adhésif de l'écran est vraiment faible donc vous ne devriez pas avoir besoin de le chauffer une seconde fois. Cependant si l'adhésif semble difficile à couper à certain endroits, vous pouvez chauffer la zone concernée pendant une minute et recommencer.

    • Insérez un autre médiator dans le bord droit du téléphone, dans un angle déjà ouvert, pour éviter d'abîmer le panneau OLED.

    • Faites glisser le médiator le long de la partie inférieure du téléphone pour couper l'adhésif.

    • Il y a un câble fragile sous le coin inférieur droit de l'écran. Si vous sentez que votre médiator reste accroché à quelque chose, retirez-le et réessayez. Assurez-vous que votre médiator est incliné vers le bas et inséré aussi peu que nécessaire pour séparer l'adhésif (pas plus de 2 mm de profondeur).

    • Laissez le deuxième médiator en place pour éviter que l'adhésif ne se recolle.

    Top and bottom edge adhesive were much stronger than this suggests. Corners were very hard to detach. I killed my screen b/c I cracked it at the top. Worked better with heating around whole perimeter like an iPhone.

    Erik Sorensen - Réponse

    WARNING: Be very careful prying the bottom left and right corners! In fact do not insert anything there because there is only a 0.8mm clearance between the screen and the edge, and there's a 0.5mm space between the screen and front glass where if you insert a pick between the screen will crack and break! I had to replace the screen after only doing a battery repair...

    bloc - Réponse

    Unfortunately I did not properly read the comments here. So for the unafraid people like me:

    DO NOT insert something into the bottom right! Especially not like it is shown in the image at this location!

    Instead I suggest start releasing the screen from right, then left side, then top and as the last step release the bottom, but start with the left corner. Do not pry too much and use a bit more heat as suggested.

    There is a small image of this critical right corner in Step 16 (the part at the top is the display and the left corner at the top is the critical right corner here). You'll see the orange cable in the corner which is easy to damage...

    Peter - Réponse

    N’allez pas en bas au début faite le haut d’abord j’ai tuer m’on écran

    Jironi - Réponse

    I can second the warnings - especially at the lower corners the OLED screen is extremely sensitive to breaking - as has happened in my attempt when inserting the pick 2 mm.

    Patrick Bohn - Réponse

    The display flex is directly on the bottom of the phone. Be very careful when goign around the bottom to not hit the display flex!!!

    FixItAgain - Réponse

  7. Remplacement de l'écran du Google Pixel 4a: étape 7, image 1 de 3 Remplacement de l'écran du Google Pixel 4a: étape 7, image 2 de 3 Remplacement de l'écran du Google Pixel 4a: étape 7, image 3 de 3
    • Insérez un troisième médiator à un angle inférieur déjà ouvert pour éviter d'endommager le panneau OLED.

    • Utilisez-le pour couper l'adhésif du bord gauche de votre téléphone.

    • Si l'adhésif semble résister, chauffez-le pendant une minute et réessayez.

    • Laissez le médiator inséré le long du bord gauche de l'écran pour éviter que l'adhésif ne se recolle.

    The display flex is directly on the bottom of the phone. Be very careful when goign around the bottom to not hit the display flex!!!

    FixItAgain - Réponse

  8. Remplacement de l'écran du Google Pixel 4a: étape 8, image 1 de 3 Remplacement de l'écran du Google Pixel 4a: étape 8, image 2 de 3 Remplacement de l'écran du Google Pixel 4a: étape 8, image 3 de 3
    • Une petite grille couvre le haut-parleur interne en haut de l'écran. Si vous n'avez pas de grille de remplacement, attention à ne pas abîmer ou perdre ce composant.

    • Insérez un quatrième médiator le long du bord gauche du téléphone, dans un angle déjà ouvert pour éviter d'endommager le panneau OLED.

    • Faites-le glisser le long du bord supérieur du téléphone pour couper l'adhésif.

    • Si l'adhésif est dur à couper, chauffez le haut de l'écran pendant une minute et recommencez.

    The display flex is directly on the bottom of the phone. Be very careful when goign around the bottom to not hit the display flex!!!

    FixItAgain - Réponse

  9. Remplacement de l'écran du Google Pixel 4a: étape 9, image 1 de 2 Remplacement de l'écran du Google Pixel 4a: étape 9, image 2 de 2
    • Une fois que vous avez découpé l'adhésif sur tout le pourtour du téléphone, soulevez délicatement le bord droit de l'écran, en ouvrant le téléphone comme un livre.

    • N'enlevez pas l'écran pour le moment.

    • Utilisez un médiator pour couper les restes éventuels d'adhésif.

  10. Remplacement de l'écran du Google Pixel 4a, Retourner l'écran: étape 10, image 1 de 3 Remplacement de l'écran du Google Pixel 4a, Retourner l'écran: étape 10, image 2 de 3 Remplacement de l'écran du Google Pixel 4a, Retourner l'écran: étape 10, image 3 de 3
    • Soulevez le haut de l'écran et basculez-le par-dessus le bord inférieur jusqu'à pouvoir le poser face vitrée sur la table.

    • Attention à ne pas tirer sur la nappe encore attachée à l'écran.

    FR : Précision : La nappe a un bout d'adhésif sur la structure du téléphone, il faut bien faire attention de le décoller. Je viens de tuer la nappe de mon écran qui était fonctionnel...

    EN : Advice : The ribbon cable is fixed to the structure with a small piece of adhesive. It should be remove prior to anything else. I just killed the ribbon cable of my perfectly used to work screen...

    Arnaud Parrot - Réponse

  11. Remplacement de l'écran du Google Pixel 4a, Déconnecter l'écran: étape 11, image 1 de 1
    • Utilisez une pincette pour délicatement décoller le ruban adhésif noir qui recouvre le cache du connecteur.

    • S'il est en bon état, vous pourrez le réutiliser au réassemblage. Sinon, remplacez-le par un morceau de ruban adhésif isolant.

    How critical is the tape that covers this connector? I realized upon sealing back up my device that I forgot to re-install it. I imagine it mostly is there to prevent dust and moisture ingress?

    Alex Cook - Réponse

    Interestingly this tape was missing in my phone. Maybe that explains some of the display issues I occasionally had, like a thin green line on the right side of the screen which could be "pushed" away.

    Fabian Seyfried - Réponse

  12. Remplacement de l'écran du Google Pixel 4a: étape 12, image 1 de 1
    Outil utilisé dans cette étape :
    Magnetic Project Mat
    $19.95
    J'achète
    • Utilisez un tournevis Torx T3 pour retirer les deux vis de 2,1 mm qui tiennent le cache du connecteur.

    • Tout au long de la réparation, gardez la trace de chaque vis et assurez-vous que chacune d'elles revienne à son emplacement d'origine.

    A T4 driver worked for me here.

    Gabe Maayan - Réponse

    It is definitely a T4.

    Jarl Friis - Réponse

    Funny ... For me, it was T3. The screws must vary across different phones

    Helmut Sporgersi - Réponse

  13. Remplacement de l'écran du Google Pixel 4a: étape 13, image 1 de 1
    • Utilisez des pincettes pour retirer le cache du connecteur de l'écran.

    • Mettez ce composant de côté pour le réinstaller au remontage.

  14. Remplacement de l'écran du Google Pixel 4a: étape 14, image 1 de 2 Remplacement de l'écran du Google Pixel 4a: étape 14, image 2 de 2
    • Utilisez la pointe d'une spatule (spudger) pour déconnecter la nappe de l'écran.

    • Pour reconnecter les connecteurs pop comme celui-ci, alignez soigneusement le connecteur sur sa prise et appuyez avec le bout du doigt – d'abord d'un côté, puis de l'autre – jusqu'à ce qu'il s'enclenche.

    • N'appuyez pas au milieu du connecteur tant qu'il n'est pas complètement en place. S'il est mal aligné, le connecteur risque de se plier et d'être endommagé de façon irréversible.

    No, why the tip? Use the other flat side that doesn't concetrate all the power on one point and Youre doing a propper job.

    Aleksandar Dejanovic - Réponse

    Only the tip is needed to lift a bit one of the sides and it will pop out. No pressure/power!

    Steve Stavropoulos -

  15. Remplacement de l'écran du Google Pixel 4a, Retirer l'écran Google Pixel 4a: étape 15, image 1 de 3 Remplacement de l'écran du Google Pixel 4a, Retirer l'écran Google Pixel 4a: étape 15, image 2 de 3 Remplacement de l'écran du Google Pixel 4a, Retirer l'écran Google Pixel 4a: étape 15, image 3 de 3
    • Retirez l'écran.

    • Pour installer le nouvel écran :

    • Vérifiez si votre écran de remplacement est doté d'une grille de haut-parleur et d'un adhésif en haut préinstallés.

    • Si c'est le cas, vous n'aurez pas besoin de l'adhésif du haut.

    • Si ce n'est pas le cas, retirez le grand film protecteur de l'adhésif du haut et appliquez-le sur l'écran (pas sur le châssis). Assurez-vous que la plus grande découpe est alignée avec la grille du haut-parleur.

    • Suivez ce tutoriel si vous utilisez des bandes adhésives découpées sur mesure.

    • Utilisez la troisième photo comme référence pour positionner vos adhésifs.

    • Pendant le premier démarrage après le remontage, l'écran passera par une phase de calibrage. Ne touchez pas l'écran pendant ce processus, car cela pourrait perturber le calibrage et poser des problèmes de tactile.

    This step seems to imply that a screen replacement is necessary when replacing the charging port. Is the charging port replaceable without replacing the screen? I understand great care must be taken not to damage the original screen in the procedure, but can it be reinstalled?

    David-Alexandre Tremblay - Réponse

    Yes, it can be reinstalled.

    Sam Omiotek -

    How long does the calibration process typically take? What does this process look like?

    phelpsbc - Réponse

    Just a heads up: If you are like me and you have accidentally turned on your Pixel 4a at some point while trying to pry the screen, don't worry too much. I was able to just connect my display with the device on. Nothing will happen until you reboot, and then the screen will initialize.

    Alex Cook - Réponse

    It would help to add that the new screen is reattached after adding glue to phone body, not the screen. With the iFixit screen adhesive pieces, a guide to which piece goes where would help also. For that I used this picture: Google Pixel 4a Display Adhesive - Genuine. Yet that is not enough as there is a cover for (speaker?) which is not clear how to apply that.

    markjville - Réponse

    The repair kit comes with Google Pixel 4a Display Adhesive - Genuine but there is no guide on how to apply that adhesive. I sent an email, but Ifixit won't make an instruction page for this.

    Mark - Réponse

    To explain how the adhesive sold by iFixit works, the actual adhesive is the black strip which is held between two pieces of plastic. Line up the pieces with the clear plastic side down. Note that some pieces may be stuck in the box they came in, the plastic is staticky. I recommend that before attaching the new screen you put each piece in place. Remove the clear plastic and place the pieces in place with the colored plastic facing up. The goal is to have the black adhesive strip on the little ledge between the edge and the depression inside the phone. It's the place where you hopefully spent time cleaning out the original adhesive. Place the corners first, then the edges. Press them into place carefully. Before removing the colored plastic attach the phone screen cable and secure it. REMEMBER TO PLACE THE ELECTRICAL TAPE OVER THE CONNECTOR (I forgot to). Then remove the colored plastic, leaving behind the adhesive, and push the screen into place.

    Karzyn - Réponse

    Of note: the seal peace at the top goes under the speaker screen, and the seal looks at first like it is reversed. To install that one accurately adhere it to the Screen itself not the body of the phone. align it where there is a see through circle along the seam and a hole in the adhesive. the sealant should run below the speaker screen. When readhering the screen to the body, remove the plastic guides around the body, then last the seal on the screen and align and install.

    USAF MX - Réponse

    Super, c'est vraiment à la portée de tout le monde, il faut juste un peu de patience et d'audace.

    Je viens de réussir le remplacement de mon écran et c'est impec !

    Il n'y a que sur la première partie, où il faut insérer le médiateur, que ça a été compliqué pour moi. Impossible de l'insérer du côté des boutons (à droite donc), par contre quand je me suis décidée à tester en passant par l'autre côté, c'est venu tout seul.

    Aussi il m'a fallu un certain temps pour comprendre que sur les adhésifs, seul le trait noir colle, et c'est donc à lui qu'il faut faire attention.

    Pensez à vérifier que l'écran est fonctionnel avant de le recoller, à mon premier essai la nappe n'était pas bien insérée et j'ai du recommencer l'insertion. Voila, prendre son temps et vérifier que tout va bien à chaque étape et c'est très facile. J'ai mis un peu moins d'une heure.

    Caroline Leleu - Réponse

    I have no idea what to do with the speaker cover mesh. It is on the display I ordered from fix it, but there is blue plastic tape over it, too, so in order for a speaker to work I'd expect the blue sticky tape needs to be removed, but it nowhere says anything about it.

    deadrom - Réponse

    After I clipped the screen in place, I realized that I had forgotten to reattach the screen bracket from step 14. Do you think this is dangerous? Can anyone assess this? In any case, the smartphone turns on and actually makes a good impression.

    Many thanks in advance for your assessment!

    Kind regards

    Tom

    Timon Roosen - Réponse

    Just some advice before you install the screen regarding the earphone grille/mesh at the top.

    Something I experienced, was that the speaker grille did not end up being seated quite right when the phone display was stuck down. It is slightly bent, and the top edge is stuck out at a slight angle - it is quite sharp and does not take much to catch a finger on it, when the phone is out of a protective case.

    I think this was because I laid the screen in, starting from the top and with it up at quite a steep angle, then working from top to bottom. I would suggest that when setting the new display within the device, that you align the bottom edge first instead.

    I am not going to risk lifting the new display to try and re-seat this grille properly, the display cost me a bloody fortune (around 58% of the phone's original price) and I am not risking breaking it over something as minor as that.

    nb. I definitely removed all the coloured plastic protective pieces before installing the new screen into the phone.

    Andrew - Réponse

Conclusion

Comparez votre pièce de remplacement à la pièce d'origine. Il se peut que vous ayez besoin de transférer des composants ou de retirer des bandes adhésives avant d'installer la nouvelle pièce.

Pour réassembler votre appareil, suivez les étapes ci-dessus dans l'ordre inverse.

Amenez vos déchets électroniques à un recycleur certifié.

La réparation Pixel 4a ne s'est pas déroulée comme prévu ? Consultez la section Pixel 4a de notre Forum pour obtenir de l'aide au diagnostic.

71 autres ont terminé cette réparation.

Merci à ces traducteurs :

en fr

100%

Ces traducteurs nous aident réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›

Sam Omiotek

Membre depuis le 02/25/19

71 951 Réputation

288 tutoriels rédigés

31 commentaires

Really nice repair guide. But no place to buy the screen.

jeffreyjantos - Réponse

Yep, still waiting for it to be available.

Paul -

Same, still waiting. I have a broken pixel 4a and I have a right to repair it.

Erik Fry -

Where do you recommend that I purchase the Pixel4a screen replacement from? I found these two with Witrigs being cheaper, but not sure if either are reliable high quality screens.

https://www.witrigs.com/oem-screen-repla...

https://phoneremedies.com/collections/go...

Alejandro Gaytan - Réponse

@samomio Where do we install the double-sided tape for the replacement? Any areas we should not cover? I tried UV glue, but it is not holding the display securely.

Paul - Réponse

Install the double-sided tape in the space between the outside edge of the glass and the OLED screen, all the way around.

Sam Omiotek -

Question- why does every phone repair shop automatically replace both the glass layer and the lcd layer even if the glass is the only thing that is broken?

T_Thyme - Réponse

Good question—because OLED screens are destroyed by the oxygen in the air once their screens are cracked or separated.

Sam Omiotek -

Hey, nice guide!! Do you know if the Pixel 4a and 4a 5G are interchangeable between them? Thanks!!

Eli Pinheiro - Réponse

Thank you! The 4a and 4a 5G screens are not interchangeable. The 5G is larger.

Sam Omiotek -

Excellent guide.

I bought this screen from eBay: https://www.ebay.de/itm/402564264411

Already had tools in an iFixit kit.

Also bought some 1mm Tesa Tape from iFixit to glue the screen back on.

Matt Smith - Réponse

Got a replacement screen off Amazon, had a major scare tho, I tested it before going deep into the repair process, worked fine, removed all the adhesive, reattached the replacement screen it it was all black. Like dead. Phone was still vibrating, I made sure nothing was covering the proximity sensors or anything, still dead screen. I take a break, come back, dis-attach and reattach and the screen several times and its working again. Weird, but now very scared I delicately put it all back together. Make sure you transfer over the speaker grill on top, it doesn’t come with most replacement screens.

Anthony Ramirez - Réponse

Hey guys & Ifixit team… what kit it s better to use for smartphones as a beginner : Essential Electronic or iOpener or Smartphone Repair Kit ?

The big pbl is finding the display…anybody bought form alibaba / alliexpres? Thanks a lot!

Daniel Spatariu - Réponse

Water damage all over the screen from about 2 TBs drop of water on it. Picked up the phone and wiped it thinking its nothing . MAN God know I was wrong. The screen literally SIP water from the sides. 3 Days later and the screen is done. WARNING : If ANY water is left for a couple seconds PRAY. Now ALL of the screen is now purple from water stuck inside it. NEVER AGAIN GOOGLE.

Samud 78 - Réponse

CAN SOMEONE TELL ME IF IT IS IMPORTANT TO BUY THE CORRECT SCREEN VERSION NUMBER? AS PIXEL 4A 4G G025 /G025N /GA02099.

Because sellers don't specify it, is it really relevant? They just sell as Pixel 4A 4G compatible.

Thanks overall!

Brian Diaz - Réponse

Great repair guide, help me a lot! I am totally peaceful now handling my phone open-hearted (with Essentiel Electronics Toolkit). I bought my new screens on piecetelephone.fr, received in 2 weeks. I used B-7000 to glue the new screen back on. Thanks a lot iFixit team :)

Tim - Réponse

where do I buy the actual google pixel 4a screen itself? On Amazon? On eBay? Pls answer me

Wei on Huang - Réponse

Replacement screens are now available from iFixit here.

Andrew S -

Where do I buy the google pixel 4a screen itself? Which website? And is it cheaper to buy the toolkit bundle or Buy the speelste tools one by one

Wei on Huang - Réponse

Phone will not power up after dropping in bowl of water. Can anything be done to recover.

Chris

Chris Lawson - Réponse

Be aware that removing a shattered screen will be tedious and you must be patient and careful to remove all of the bits from the glue channel between the screen and the phone body. Removing the old glue is a VERY tedious and time consuming process so be prepared to take considerably longer than the 30-60 minutes shown in the directions. Also be aware that having a magnifiying headset with lights should be a high priority purchase along with this kit. Re-attaching the screen-to-phone connector is also incredibly tedious and frustrating. It took more than 8 hours of work to get ours replaced. At first it all worked fine and 10 minutes later the screen failed. Be prepared to either be delighted that your efforts bring a phone back to life or that it will end in utter failure and frustration... it is NOT as easy as you think. The YouTube videos are all missing this information and make it all look easy...... not so.

D. J. - Réponse

If you get the kit that includes the adhesive strips, save yourself the risk and irritation and just get some B-7000 or whatever you see someone using in a YouTube tutorial. They seem to work, but it doesn't seem like they're actually cut for specifically this phone, or in my case none of the shapes really came close to aligning with any cutouts or holes. They only give you exactly what you need, so if you accidentally fail to line it up exactly right, you're stuck trying to maneuver this string of very sticky goop into a precise line or corner.

Otherwise, the tools are exactly what you need in a food way, very little waste and decent packaging. Great value overall, the screen is legit, although now my proximity sensor isn't working for some reason. They're pretty good quality, I'll keep it all around, but will be ordering some better adhesive and maybe redoing it. It really is not fun working with those, and I'd appreciate more for my money in that respect.

Also the picks aren't thin enough, risky using them.

L. T - Réponse

I have problems with my proximity sensor, too. I'll open the phone again to see if it gets fixed.

carlitossuper1 -

That was really useful. Thanks for the info and clear steps. I did end up having to push the middle of the connector when reattaching the screen.

Eanna Ryan - Réponse

When the kit is going to be available?

Karna Soneji - Réponse

After advice please - have been using my 4a with cracked screen for a while, but after dropping it last week the screen had a green intermittent flash across it, and nothing else. Pressing the power button to switch off seemed to have no effect. Can anyone please advise whether they think a new screen will resurrect it, or does it sound as though I have broken something else too? Thanks!

Rachel - Réponse

After having followed this guide and successfully replaced my screen, I have to say that it stops rather abruptly. It is very detailed, but then it says "apply the strips by following a generic give and put it together again" which is the most tedious part and should be documented. There should be a guide for where which adhesive part belongs, as some have differences just in millimeter scale. Eventually, I noticed that the product page for the adhesive has a picture showing the pieces aligned correctly. Contrary to what is shown in the linked generic adhesive guide, those are supposed to be applied to the device housing, not the screen.

Also, you should NOT apply the top adhesive, as one comes pre-applied to the screen.
There was also an Earpiece Speaker Mesh pre-applied to my new screen, in addition to the one that comes extra, so don't apply the other one on top! In my case, the Mesh was pre-applied inside-out, which I realized just a second before pressing the screen onto the adhesive for good.

1/2

R0M4N - Réponse

2/2
When it comes to making sure the mesh is aligned correctly, special attention is required. The slightly shorter side of the mesh is supposed to be the bottom side, which means the picture on the product page currently shows it upside-down.

Those are my main gripes with this guide and I think their omission sets newbies up for failure and frustration, which I would assume is the opposite of what ifixit wants when promoting self-repare and should not exist for an “official” self-repare done together with google.

Small additions:
Step 14 tells you to re-attach the connector by clicking in one side first, then the other. I am pretty sure that it means to say and should be pressing down coming from the top edge, then the bottom (or the other way around), but not the sides as in left and right, which is exactly what would make it misaligned.
Also, I would emphasize that if the plastic is not smooth after the removed old adhesive, it is almost certainly hard dried glue. Scrub with the cleaning alcohol pad here.

R0M4N - Réponse

Adhesive kit has a long blue side and a long red side. I guess the red side goes right, seen from top, as the image and the mentioning of the red strip in the disassembly suggestest, but am I sure? heck no.

deadrom - Réponse

Après avoir cassé mon écran, et face aux coûts annoncés par les réparateurs professionnels, je me suis lancé dans la réparation seule. De façon assez surprenante, c'était relativement facile excepté l'installation de l'adhésif qui demande beaucoup de minutie. Je conseille l'achat d'un pack d'adhésif supplémentaire pour être plus serein.

Pour l'instant tout a l'air de très bien marcher, je recommande grandement.

gardi - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 70

7 derniers jours : 468

30 derniers jours : 2,203

Total : 172,657