Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Introduction
Ce guide va vous montrer comment remplacer l'écran abîmé de votre LG G3
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the battery out of its recess and remove it.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the eight Phillips #00 screws (4 mm length).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert an opening pick between the bottom right corner of the motherboard cover and the motherboard.
-
Pry up the motherboard cover to open the plastic clips which hold the cover in its place.
-
Work your way along the right edge.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Carefully lift the right edge of the motherboard cover.
-
Remove the motherboard assembly.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to pry up and disconnect the display flex cable.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to pry up and disconnect the digitizer flex cable.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to pry up and disconnect the rear camera flex cable.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to pry up and disconnect the front camera flex cable.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Slide an opening pick under the bottom right corner of the motherboard and slowly pry it out of its recess by rotating the opening pick sideways.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Slide the opening pick under the right edge of the motherboard where the SIM card slot is located and pry it up by rotating the opening pick sideways.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grab the top section of the motherboard and carefully lift it out of the phone.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a pair of tweezers to remove the earpiece speaker.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a pair of tweezers to remove the front camera.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a pair of tweezers to remove the rear camera.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert one of the tweezer arms under the vibration motor and pry it up.
-
Remove the vibration motor.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Apply a heated iOpener to the bottom end of the screen to loosen the adhesive underneath.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the pointed end of a spudger to pry up the headphone jack and remove it with a pair of tweezers.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a pair of tweezers to carefully pry up and remove the daughterboard at the bottom end of the screen assembly.
-
Pour réassembler votre appareil, suivez les instructions précédentes dans l'ordre inverse.
Pour réassembler votre appareil, suivez les instructions précédentes dans l'ordre inverse.
Annulation : je n'ai pas terminé ce tutoriel.
129 autres ont terminé cette réparation.
Merci à ces traducteurs :
0%
Ces traducteurs nous aident réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›
42 commentaires
Ok so after I did all this my screen is black and so I ordered a second screen and also nothing the phone works great and makes noises also touch responds but nothing on lcd just black can you help me with this also if I take battery out and plug up charger it shows a battery warning on lcd so clearly it works
Has it sustained any water damage?
Did you get it working i have the same issue? the picture displays with the original screen but not with the new one. i have tried 3 different screens and get the same on all of them. i even tried updating to the latest software but only get a black screen, no picture.
When i have had this on iphones i just so a reset by holding down the buttons and the screen starts to work.
Please someone help
Matt -
Same here! I also findout that lcd still works, if you get some flashlight on screen in a dark room, you will see that only backlight not working when battery plugged. I tried to baking it but it still didn't worked. It's obvious that backlight could properly operate as it works when you take off the battery. I'm looking for solutions, if I find any, will wrote it here.
Did someone find a solution to this? I also replaced my screen and it keeps black solid when I turn it on, even with the touch working properly.