Aller au contenu principal

Introduction

This guide required

  1. Using a Phillips #1 screwdriver, remove the 4.8mm screw on the battery cover by twisting the screwdriver counter-clockwise. Using a Phillips #1 screwdriver, remove the 4.8mm screw on the battery cover by twisting the screwdriver counter-clockwise.
    • Using a Phillips #1 screwdriver, remove the 4.8mm screw on the battery cover by twisting the screwdriver counter-clockwise.

  2. Remove the two AAA batteries by pulling on one end of the battery and lifting it straight out. Remove the two AAA batteries by pulling on one end of the battery and lifting it straight out. Remove the two AAA batteries by pulling on one end of the battery and lifting it straight out.
    • Remove the two AAA batteries by pulling on one end of the battery and lifting it straight out.

  3. When reassembling, align the notch on the battery panel with the slot on the phone. When reassembling, align the notch on the battery panel with the slot on the phone. When reassembling, align the notch on the battery panel with the slot on the phone.
    • When reassembling, align the notch on the battery panel with the slot on the phone.

  4. Remove four 13.8mm screws from the back of the device using a Phillips #1 screwdriver. Remove four 13.8mm screws from the back of the device using a Phillips #1 screwdriver.
    • Remove four 13.8mm screws from the back of the device using a Phillips #1 screwdriver.

  5. Remove a single 4.8 mm screw with a Phillips #0 screwdriver and lift away the battery pack being careful of the wires. Remove a single 4.8 mm screw with a Phillips #0 screwdriver and lift away the battery pack being careful of the wires. Remove a single 4.8 mm screw with a Phillips #0 screwdriver and lift away the battery pack being careful of the wires.
    • Remove a single 4.8 mm screw with a Phillips #0 screwdriver and lift away the battery pack being careful of the wires.

  6. Remove two 7.2 mm screws with a Phillips #0 screwdriver. Slide off the spring.
    • Remove two 7.2 mm screws with a Phillips #0 screwdriver.

    • Slide off the spring.

  7. Remove the single 7.5mm screw with a Phillips #0 screwdriver. Lift up the black plastic piece. Lift up the black plastic piece.
    • Remove the single 7.5mm screw with a Phillips #0 screwdriver.

    • Lift up the black plastic piece.

  8. Remove four 7.5mm screws with a Phillips #0 screwdriver. Remove four 7.5mm screws with a Phillips #0 screwdriver.
    • Remove four 7.5mm screws with a Phillips #0 screwdriver.

  9. Remove the two buttons, noting how wires are placed for reassembly. Remove the two buttons, noting how wires are placed for reassembly.
    • Remove the two buttons, noting how wires are placed for reassembly.

  10. Lift the button board up and away to clear room for lifting the motherboard. Tilt the assembly up but being wary that it is still attached to the front panel.
    • Lift the button board up and away to clear room for lifting the motherboard.

    • Tilt the assembly up but being wary that it is still attached to the front panel.

  11. Slide the toothed slider towards you to remove.
    • Slide the toothed slider towards you to remove.

  12. To reassemble, align the two black lines together by moving the belt back and forth.
    • To reassemble, align the two black lines together by moving the belt back and forth.

    • Once aligned reinsert the toothed slider at the exact point shown.

    be careful at the top blue button (on/off) that might come off when you align the belt

    cipriansoleriu - Réponse

Conclusion

To reassemble your device, follow these instructions in reverse order, skipping step 10 as the toothed slider has already been put in for proper alignment.

Une autre personne a terminé cette réparation.

Sean Webb

Membre depuis le 04/09/2015

384 Réputation

2 tutoriels rédigés

Équipe

USF Tampa, Team 2-4, Sullivan Fall 2015 Membre de l'équipe USF Tampa, Team 2-4, Sullivan Fall 2015

USFT-SULLIVAN-F15S2G4

3 membres

6 tutoriels rédigés

Good work !

Nice.

I did not see the black line in mine,

i opened the foil and glued it new together . Not so nice. :D

But it works.

Schwarzstein - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 8

Total : 1,078