Introduction

This repair guide will give you step by step instructions on how to remove the Macintosh PowerBook 1400c Monitor.

Turn the device upside down and then locate the battery latch near the front of the device.
  • Turn the device upside down and then locate the battery latch near the front of the device.

Ajouter un commentaire

Slide the latch to the left to release the battery.
  • Slide the latch to the left to release the battery.

Ajouter un commentaire

  • Continue holding the latch then gently pull the battery out of the device.

  • Place the battery in a safe location.

Ajouter un commentaire

  • Locate the CD-ROM Drive latch.

Ajouter un commentaire

  • Slide the latch to the right to release the CD ROM drive.

Ajouter un commentaire

  • Continue holding the latch then gently pull the CD-ROM Drive out of the device.

  • Place the CD ROM drive in a safe location.

Ajouter un commentaire

  • Locate the speaker cover.

Ajouter un commentaire

  • Press firmly on each end of the speaker cover and slide it to the left.

I found it was easy to get a spudger over the left edge and lift it up a bit, then push the bar to the left, It pops right off after that.

Jimmy James - Réponse

  • Gently lift the speaker cover to remove it.

Ajouter un commentaire

  • Lift the keyboard up from the back using a spudger(wedge side).

Ajouter un commentaire

  • Gently lift the keyboard until only the ribbon cable remains attached.

Ajouter un commentaire

  • Tilt the keyboard away from the screen.

Ajouter un commentaire

  • Locate the six screws that secure the heatsink.

This is not necessary to remove the HDD. Go directly to step 20.

Kenneth DeVries - Réponse

That isn't the HDD!

Dix Dox - Réponse

  • Remove the six screws from the heatsink using the Philips #1 screwdriver.

Ajouter un commentaire

  • Lift the heatsink from the side closest to the laptop screen.

Ajouter un commentaire

  • Remove the heatsink.

Ajouter un commentaire

  • Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.

Ajouter un commentaire

  • Detach the ribbon cable.

Ajouter un commentaire

  • Remove the keyboard.

Ajouter un commentaire

  • Identify the right and left monitor end caps.

Ajouter un commentaire

  • Pry off the end caps by putting a spudger between the monitor hinge and the end cap and prying outwards.

Ajouter un commentaire

  • Once the end cap has been loosened by the spudger, pull outwards on the end caps.

Ajouter un commentaire

  • Completely remove both end caps.

Ajouter un commentaire

  • Identify the 4 total screw under the end caps (2 under each end cap).

    • The two outside 16mm long screws

    • The two inside 5.4mm long screws

Ajouter un commentaire

  • Lay the monitor all the way back.

Ajouter un commentaire

  • Remove the 4 screws using the Phillips #0 screwdriver.

Ajouter un commentaire

  • Identify the center cap of the monitor.

Ajouter un commentaire

  • Pry the center cap off by placing the spudger between the hinge and the center cap and prying upwards.

Ajouter un commentaire

  • Detach the center cap completely.

Ajouter un commentaire

  • Identify the one 12.6mm long screw under the center cap.

Ajouter un commentaire

  • Remove the center screw with a Phillips #0 screwdriver.

Ajouter un commentaire

  • Lift upwards on the metal cover under the screw.

Ajouter un commentaire

  • Completely remove the metal cover.

Ajouter un commentaire

  • Identify where the left and right monitor cords are attached to the logic board

    • The base of the left monitor cord

    • The base of the right monitor cord

Ajouter un commentaire

  • To detach the left monitor cord grab the left monitor cord at the base of the cord and pull vertically up.

Ajouter un commentaire

  • Completely detach the left monitor cord from the logic board.

Ajouter un commentaire

  • To detach the right monitor cord grab the right monitor cord at the base of the cord and pull vertically up.

Ajouter un commentaire

  • Completely detach the right monitor cord from the logic board.

Ajouter un commentaire

  • Completely remove the monitor from the computer.

Ajouter un commentaire

Conclusion

Once the monitor has been removed, to attach the new monitor follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Taylor Chris

Membre depuis le 01/04/2011

85 Réputation

1 tutoriel rédigé

Équipe

Cal Poly, Team 10-39, Forte Spring 2011 Membre de l'équipe Cal Poly, Team 10-39, Forte Spring 2011

CPSU-FORTE-S11S10G39

5 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 8

Total : 2,506