Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Boutique

Introduction

The direction switch determines if the drill is going to rotate clockwise or counterclockwise. If this is broken it can almost render the drill useless as it will be stuck in one direction. This is a fairly simple guide.

  1. Use the flat side of a metal spudger to peel the black rubber cover off of the casing.
    • Use the flat side of a metal spudger to peel the black rubber cover off of the casing.

    • Use some force; the rubber cover is securely attached to the housing.

    • Rotate the casing until it fits onto the housing with no gaps between it and the clear cover.

    • Orientation is important when putting the rubber cover on the casing.

  2. Remove the plastic cover with your hands. There is no need to force off the plastic cover. The plastic cover should be much easier to remove than the rubber cover.
    • Remove the plastic cover with your hands.

    • There is no need to force off the plastic cover. The plastic cover should be much easier to remove than the rubber cover.

  3. Unscrew the four 16 mm long screws from the back panel with a T10 Torx Screwdriver. Use a firm grip to peel off the back panel. It is sealed tight and requires a good amount of force to remove. Use a firm grip to peel off the back panel. It is sealed tight and requires a good amount of force to remove.
    • Unscrew the four 16 mm long screws from the back panel with a T10 Torx Screwdriver.

    • Use a firm grip to peel off the back panel. It is sealed tight and requires a good amount of force to remove.

  4. SAUTEZ LA MISE À NIVEAU

    Économisez en réparant avec un kit tout-en-un.

    Fix Kits pour iPhone

    SAUTEZ LA MISE À NIVEAU

    Économisez en réparant avec un kit tout-en-un.

    Fix Kits pour iPhone
  5. Unscrew the eight 15 mm T10 Torx screws from the housing The screw hole located nearest the battery port is deep and small. Most screwdrivers with replaceable bits will not fit into the hole. Instead, use a conventional screwdriver that fits.
    • Unscrew the eight 15 mm T10 Torx screws from the housing

    • The screw hole located nearest the battery port is deep and small. Most screwdrivers with replaceable bits will not fit into the hole. Instead, use a conventional screwdriver that fits.

  6. Place the driver flat on a table before completely separating the two halves of the housing so components of the drill don't fall out during opening.
    • Place the driver flat on a table before completely separating the two halves of the housing so components of the drill don't fall out during opening.

    • Pry apart the two halves of the housing at the back side of the driver using the metal spudger.

    • The housing is easier to remove if you pry from multiple sides.

  7. Do not remove the direction switch. Pull out all electrical components from housing by hand.
    • Do not remove the direction switch.

    • Pull out all electrical components from housing by hand.

    • Lift out the motor.

    • Follow the wires.

    • The components should come out of their respective slots with ease and require little force to lift out.

    • The circuit board located nearest the battery pack and the LED light will be hard to pull out.

    • Remember to precisely place all components in their correct slots with their correct orientations when reassembling.

  8. Remove the broken direction switch.
Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Sean Liston

Membre depuis le 28/04/2015

275 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 15-5, Amido Spring 2015 Membre de l'équipe Cal Poly, Team 15-5, Amido Spring 2015

CPSU-AMIDO-S15S15G5

4 membres

12 tutoriels rédigés

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 35

Total : 767