Réparez vos affaires Communauté Boutique

Ring Stick Up Cam Camera Replacement

Introduction

In this guide, we will show you how to replace the camera in a Ring Stick Up Cam. You will need a Phillips #00 screwdriver and a plastic opening tool.

Ce dont vous avez besoin

  1. Ring Stick Up Cam Camera Replacement, Battery: étape 1, image 1 de 1

    • Remove the six 6mm Phillips #00 screws from the back of the device.

    Modifier

  2. Ring Stick Up Cam Camera Replacement: étape 2, image 1 de 1

    • Pry off the aluminum plate using a plastic opening tool.

    Modifier

  3. Ring Stick Up Cam Camera Replacement: étape 3, image 1 de 1

    • Remove the two 6mm Phillips #00 screws that were under the aluminum plate.

    Modifier

  4. Ring Stick Up Cam Camera Replacement: étape 4, image 1 de 1

    • Pry off the back cover using a plastic opening tool.

    Modifier

  5. Ring Stick Up Cam Camera Replacement: étape 5, image 1 de 1

    • Disconnect the battery power leads using a plastic opening tool.

    Modifier

  7. Ring Stick Up Cam Camera Replacement: étape 6, image 1 de 1

    • Use a plastic opening tool to loosen the adhesive holding the battery in place and remove the battery by hand.

    Modifier

  8. Ring Stick Up Cam Camera Replacement, Camera: étape 7, image 1 de 1

    • Remove the three silver 6mm Phillips #00 screws holding the motherboard in the device.

    Modifier

  9. Ring Stick Up Cam Camera Replacement: étape 8, image 1 de 1

    • Disconnect the ribbon connector shown in the photo.

    Modifier

  10. Ring Stick Up Cam Camera Replacement: étape 9, image 1 de 1

    • Remove the motherboard from the device by hand.

    Modifier

  11. Ring Stick Up Cam Camera Replacement: étape 10, image 1 de 1

    • Remove the two black 5mm Phillips #00 screws holding the camera board into the device.

    • Remove the single silver 10mm Phillips #00 screw holding the camera board into the device.

    Modifier

  12. Ring Stick Up Cam Camera Replacement: étape 11, image 1 de 1

    • Remove the three plastic spacers shown in the photo by hand.

    Modifier

  13. Ring Stick Up Cam Camera Replacement: étape 12, image 1 de 1

    • Carefully disconnect the camera board from the daughterboard by sliding a plastic opening tool between the camera board and the daughterboard.

    Modifier

  14. Ring Stick Up Cam Camera Replacement: étape 13, image 1 de 1

    • Lift the camera board out of the housing using your hand.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 3 autres contributeurs

Ao Li

Membre depuis le 02/06/19

245 Réputation

1 tutoriel rédigé

Badges: 7

+ 4 badges supplémentaires

Équipe

UC Davis, Team S18-G3, Lore Winter 2019 Membre de l'équipe UC Davis, Team S18-G3, Lore Winter 2019

UCD-LORE-W19S18G3

3 membres

8 tutoriels rédigés

2 commentaires

Where can I purchase a new lens?

Javier Casas - Réponse

Any ideas where to get a new lens?

Mete Doguoglu - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 13

30 derniers jours : 40

Total : 4,453