Réparez vos affaires Communauté Boutique

Ryobi RJ1861V Motor Replacement

Introduction

This replacement guild will should how to replace the motor in the Ryobi RJ1861V.

Ce dont vous avez besoin

  1. Ryobi RJ1861V Motor Replacement, Saw Bar Assembly: étape 1, image 1 de 1

    • Use a Torx T5 screwdriver to remove the single 8 mm screw securing the shoe.

    Modifier

  2. Ryobi RJ1861V Motor Replacement: étape 2, image 1 de 2 Ryobi RJ1861V Motor Replacement: étape 2, image 2 de 2

    • Remove the rubber sleeve.

    • You may have to use some force as it has a tight fit.

    Modifier

  3. Ryobi RJ1861V Motor Replacement: étape 3, image 1 de 1

    • Use a Torx T5 screwdriver to remove the six screws on the underside of the device.

    Modifier

  4. Ryobi RJ1861V Motor Replacement: étape 4, image 1 de 1

    • Use a Torx T5 screwdriver to remove the four screws on the top of the gear case.

    • There are two screws on each side of the device.

    Modifier

  5. Ryobi RJ1861V Motor Replacement: étape 5, image 1 de 1

    • Remove the backside panel.

    Modifier

  6. Ryobi RJ1861V Motor Replacement: étape 6, image 1 de 1

    • Unscrew the four T5 Torx screws that hold the assembly bar in place.

    Modifier

  7. Ryobi RJ1861V Motor Replacement: étape 7, image 1 de 1

    • Lift the assembly bar up and out of the chassis.

    Modifier

  8. Ryobi RJ1861V Motor Replacement, Assembly Bar Bearing: étape 8, image 1 de 1

    • Begin with the top of the device facing up.

    Modifier

  9. Ryobi RJ1861V Motor Replacement: étape 9, image 1 de 1

    • Insert needle nose pliers to remove the retaining pin at the top of the bearing.

    Modifier

  10. Ryobi RJ1861V Motor Replacement: étape 10, image 1 de 1

    • Once the retaining pin has been removed, pull off the damaged bearing and insert a new one.

    Modifier

  11. Ryobi RJ1861V Motor Replacement, Motor: étape 11, image 1 de 1

    • The motor is divided into two sections, one attached to the gear case and one attached to the handle.

    • This arrow indicates the section attached to the gear case.

    • This arrow indicates the section attached to the handle.

    Modifier

  12. Ryobi RJ1861V Motor Replacement: étape 12, image 1 de 3 Ryobi RJ1861V Motor Replacement: étape 12, image 2 de 3 Ryobi RJ1861V Motor Replacement: étape 12, image 3 de 3

    • Use a Torx T5 screwdriver to remove the four screws attaching the motor to the gear case.

    Modifier

  13. Ryobi RJ1861V Motor Replacement: étape 13, image 1 de 1

    • Use a Torx T5 screwdriver to remove the two screws inside the motor housing of the handle.

    Modifier

  14. Ryobi RJ1861V Motor Replacement: étape 14, image 1 de 2 Ryobi RJ1861V Motor Replacement: étape 14, image 2 de 2

    • Remove the four screws on the back of the housing with a Torx T5 screwdriver.

    • Flip the housing over and pull the motor up and out of the housing.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 6 autres contributeurs

Adrian Williams

Membre depuis le 04/08/19

183 Réputation

1 tutoriel rédigé

Badges: 3

Équipe

Eastern Washington University, Team S1-G1, Rowley Spring 2019 Membre de l'équipe Eastern Washington University, Team S1-G1, Rowley Spring 2019

EWU-ROWLEY-S19S1G1

3 membres

3 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 9

30 derniers jours : 27

Total : 255