Réparez vos affaires Communauté Boutique

SG 552-1 Commando Barrel Replacement

Introduction

This guide will be showing step-by-step instructions on how to get to and replace the barrel of the airsoft gun.

Ce dont vous avez besoin

  1. SG 552-1 Commando Barrel Replacement, Barrel: étape 1, image 1 de 2 SG 552-1 Commando Barrel Replacement, Barrel: étape 1, image 2 de 2

    • Using a flathead screwdriver, remove the pin holding the hand guard in place.

    • To remove this, turn the pin clockwise and push it through at the same time.

    • Pull the hand guard off.

    Modifier

  2. SG 552-1 Commando Barrel Replacement: étape 2, image 1 de 2 SG 552-1 Commando Barrel Replacement: étape 2, image 2 de 2

    • Using a Phillips #1 screwdriver, remove the two 8mm screws above the hand guard on both sides of the gun. There should be four total.

    Modifier

  3. SG 552-1 Commando Barrel Replacement: étape 3, image 1 de 2 SG 552-1 Commando Barrel Replacement: étape 3, image 2 de 2

    • Locate the button to fold over the folding stock and fold over the folding stock.

    • Using a Phillips #1 screwdriver, remove the 20mm screw located behind the folding stock.

    Modifier

  5. SG 552-1 Commando Barrel Replacement: étape 4, image 1 de 2 SG 552-1 Commando Barrel Replacement: étape 4, image 2 de 2

    • Turn the gun over so that you are facing the bottom of the gun.

    • Using a Phillips #1 screwdriver, remove the following screws:

    • Remove the 8mm screw located directly underneath the cocking lever.

    • Remove the 8mm screw beside the one you just removed.

    Modifier

  6. SG 552-1 Commando Barrel Replacement: étape 5, image 1 de 2 SG 552-1 Commando Barrel Replacement: étape 5, image 2 de 2

    • Carefully tug on the tip of the gun and pull the barrel and its cover out.

    Modifier

  7. SG 552-1 Commando Barrel Replacement: étape 6, image 1 de 3 SG 552-1 Commando Barrel Replacement: étape 6, image 2 de 3 SG 552-1 Commando Barrel Replacement: étape 6, image 3 de 3

    • Pull the barrel out from the cover.

    • Remove the pieces at the end of the barrel.

    Modifier

  8. SG 552-1 Commando Barrel Replacement: étape 7, image 1 de 2 SG 552-1 Commando Barrel Replacement: étape 7, image 2 de 2

    • Remove the remaining pieces of on the ends of the barrel.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 5 autres contributeurs

Laura Schulz

Membre depuis le 10/05/12

1 Réputation

1 tutoriel rédigé

Badges: 1

Équipe

Cal Poly, Team 18-41, Regan Fall 2012 Membre de l'équipe Cal Poly, Team 18-41, Regan Fall 2012

CPSU-REGAN-F12S18G41

6 membres

6 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 2

Total : 1,642