Réparez vos affaires Communauté Boutique

Samsung CLP-300 Black Toner Transfer Unit Replacement

Introduction

Follow these steps if you are experiencing uneven print quality or lines in your printed documents.

Ce dont vous avez besoin

  1. Samsung CLP-300 Black Toner Transfer Unit Replacement, Black Toner Transfer Unit: étape 1, image 1 de 1

    • Turn the printer off and wait a few minutes for it to cool.

    Modifier

  2. Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 2, image 1 de 1

    • Pull paper tray out and set aside.

    Modifier

  3. Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 3, image 1 de 2 Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 3, image 2 de 2

    • Open the front cover.

    Modifier

  4. Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 4, image 1 de 1

    • Pull the waste toner container out of the printer using the handle.

    • Make sure to keep waste toner container upright to avoid spillage.

    Modifier

  6. Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 5, image 1 de 3 Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 5, image 2 de 3 Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 5, image 3 de 3

    • Pull the imaging unit out of the printer using bottom handle.

    • Use green handle on top of imaging unit to steady unit as you pull it out.

    • At this point you can set the printer aside as you will only need the imaging unit to continue repair.

    Modifier

  7. Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 6, image 1 de 2 Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 6, image 2 de 2

    • Remove these two screws.

    • Do not expose imaging unit to light for more than a few minutes. Covering unit with a piece of paper is sufficient protection while you complete repair.

    Modifier

  8. Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 7, image 1 de 1

    • Carefully pry plastic arm away from main unit.

    Modifier

  9. Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 8, image 1 de 3 Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 8, image 2 de 3 Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 8, image 3 de 3

    • Carefully pry plastic from screw base so that the entire organic photo conductor piece slides open to the left.

    • When removing the organic photo conductor take care to not lose the small spring on the back left.

    • At this point you may want to put on plastic gloves to keep from staining hands with printer ink.

    Modifier

  10. Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 9, image 1 de 2 Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 9, image 2 de 2

    • Slide each toner transfer unit out separately, placing all aside except for the black toner transfer unit.

    • Keep toner rollers level to avoid toner spillage.

    Modifier

  11. Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 10, image 1 de 3 Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 10, image 2 de 3 Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 10, image 3 de 3

    • Remove these five screws from the top of the black toner transfer unit.

    • Remove main and smaller z-shaped plates.

    Modifier

  12. Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 11, image 1 de 2 Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 11, image 2 de 2

    • Remove these three screws from the right end of the toner transfer unit.

    Modifier

  13. Samsung CLP-300 Black Toner Transfer Unit Replacement: étape 12, image 1 de 1

    • Remove plastic end piece.

    • Gently pull out black toner roller.

    • Insert new roller in place of old roller turning slightly to fit.

    • Be careful not to pinch small foam square when inserting new roller.

    • Cover new roller with toner by rotating roller by hand.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autres ont terminé cette réparation.

Auteur

avec 5 autres contributeurs

Heather Howard

Membre depuis le 10/15/14

586 Réputation

4 tutoriels rédigés

Badges: 8

+ 5 badges supplémentaires

Équipe

University of Maine, Team 1-1, Diaz Fall 2014 Membre de l'équipe University of Maine, Team 1-1, Diaz Fall 2014

UMAINE-DIAZ-F14S1G1

3 membres

8 tutoriels rédigés

2 commentaires

I need more information pertaining step 8. In order to separate the parts, in which directions should the be moved first and where is the best point to apply force ?

Bernd Dreyer - Réponse

I need more information for step 12: I removed the old roller. Unfortunately I don't know anymore how exactly the metal discs and the white plastic rings are placed.

Daniel Roller - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 4

30 derniers jours : 15

Total : 3,288