Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Ce dont vous avez besoin

  1. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 1, image 1 de 3 : étape 1, image 2 de 3 : étape 1, image 3 de 3
    • Remove the back cover of phone by lifting up on the back cover tab with the blue plastic opening tool.

    • Go around the edge of the back cover to completely remove it.

  2. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 2, image 1 de 3 : étape 2, image 2 de 3 : étape 2, image 3 de 3
    • Remove the old battery by lifting up on the thumb tab.

    • Periodically clean the brass terminals on the battery and the phone. Place a minute amount of ISO on a Q-tip and gingerly clean the connections.

  3. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 3, image 1 de 3 : étape 3, image 2 de 3 : étape 3, image 3 de 3
    • Remove the nine 4mm screws screws from the midframe with a Phillips #000 screwdriver.

  4. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 4, image 1 de 2 : étape 4, image 2 de 2
    • Wedge the blue plastic opening tool in between the front and side panel.

    • Move the blue plastic opening tool around the edges between the front and side panel.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 5, image 1 de 2 : étape 5, image 2 de 2
    • Make sure that you detach the mid-frame from the inside too.

  6. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 6, image 1 de 2 : étape 6, image 2 de 2
    • Unhook the ribbon cable clip with the plastic opening tool and remove the audio jack.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 7, image 1 de 2 : étape 7, image 2 de 2
    • Use the plastic opening tool to unhook the ribbon cable clip.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 8, image 1 de 2 : étape 8, image 2 de 2
    • Gently pull on the connector with the tweezers until the speaker comes off.

  9. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 9, image 1 de 2 : étape 9, image 2 de 2
    • Unhook the other ribbon cable clip to the screen with the blue plastic opening tool.

  10. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 10, image 1 de 3 : étape 10, image 2 de 3 : étape 10, image 3 de 3
    • Unhook the ribbon cable clip to the front camera.

    • Lift the motherboard up and out of the device.

  11. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 11, image 1 de 2 : étape 11, image 2 de 2
    • Remove the motherboard and unhook the ribbon cable clip to the back camera.

Ligne d'arrivée

86 autres ont terminé cette réparation.

Kyle Ruff

Membre depuis le 02/04/16

6 725 Réputation

5 tutoriels rédigés

Équipe

USF Tampa, Team 17-3, Blackwell Winter 2016 Membre de l'équipe USF Tampa, Team 17-3, Blackwell Winter 2016

USFT-BLACKWELL-W16S17G3

3 membres

12 tutoriels rédigés

12 commentaires

After fixing all the screen, for some reason the LCD was turning on but it showed black and i dont know if is because im missing a screw or because the LCD doesnt work?

Glo - Réponse

lol this is likely because you ruined the lcd. this tutorial forgot to mention that it is essential to apply heat, as the midframe is adhered on to the inner component.

connectedcellrepair -

Just need to get a idea on this phone, the silver backing thats usually stuck to the mid frame, when pulling out the old lcd this also came with it.

My question is whether or not that needs to replaced?

Also it changes screens all on its on.

Lisa Yates - Réponse

My grand prime 4g board damage

Rakesh - Réponse

My grand prime 4g mother board damage

Rakesh - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 16

30 derniers jours : 70

Total : 53,035