Introduction

Is the quality of your photo not up to par?

This simple guide will help you replace the front camera lens for your Galaxy Nexus.

You must open the back of the phone to access the battery. To do this use the plastic opening tools or your fingernail and insert it into the divot.
  • You must open the back of the phone to access the battery. To do this use the plastic opening tools or your fingernail and insert it into the divot.

Ajouter un commentaire

Remove the back cover of the phone by moving the prying tool or your fingernail away from the phone while it is still in the divot.
  • Remove the back cover of the phone by moving the prying tool or your fingernail away from the phone while it is still in the divot.

Ajouter un commentaire

  • Insert your finger into the divot of the battery and pull the battery towards yourself to remove.

  • This is when a new battery will be inserted.

Ajouter un commentaire

  • Remove 4.4 mm screws using a PH # 000 as indicated on the picture.

The screws need to be labeled with the head type and the length.

Spencer - Réponse

Confusing heading.

Dan Brown - Réponse

This is something that cannot be fixed. Due to it being a prerequisite guide it comes up with the title of the guide itself as it is inserted as a prerequisite guide.

Stephan Williams -

  • After removing the screws be sure to turn the phone right side up.

  • Insert your plastic opening tool between the screen and the outer case. Move the opening tool around the phone without removing it from in between the screen and the shell of the phone.

  • Pop the screen out of the outer shell. Be cautious not to damage the control board or the screen.

Ajouter un commentaire

  • Unscrew 4.4mm with a PH #000 marked screw.

Add head type for screw.

Dan Brown - Réponse

  • With the flat head screw driver pull up the blue connector.

flat-head? flat head?

Dan Brown - Réponse

Great pictures!

Dan Brown - Réponse

Don't omit articles.

Dan Brown - Réponse

  • With you finger or prying tool pull back bottom module.

You should add a step to pry off the connection on the side of the board also.

Spencer - Réponse

Change "pulled back" to "pull back."

Dan Brown - Réponse

  • Remove the internal battery using tweezers or your flat head screw driver.

  • There is glue at the bottom keeping battery and chassis stuck together.

Ajouter un commentaire

  • Peel the display connector strip off the main circuit board using the tweezers.

  • Peel the USB connector strip off the main circuit board using the tweezers.

There are 2 tabs that need to be disconnected, not just one.

Spencer - Réponse

  • Remove the antenna using either your fingers or tweezers.

Ajouter un commentaire

  • Using tweezers, pull the top circuit board off.

  • Depending on your model, there may be ribbon cable connectors attached to the underside of the board. Be careful not to rip them out of the sockets when removing the board.

Last photo is blurry.

Dan Brown - Réponse

  • Use the tweezers flip up the circuit for the front camera.

  • Use the tweezers pull out the front camera.

You should include a picture of the actual part that you are flipping up

Spencer - Réponse

Conclusion

To reassemble your device, follow these instructions in reverse order.

4 autre(s) ont terminé cette réparation.

Dae Young Yoon

Membre depuis le 22/09/2014

226 Réputation

1 tutoriel rédigé

Équipe

USF Tampa, Team 4-6, Brown Fall 2014 Membre de l'équipe USF Tampa, Team 4-6, Brown Fall 2014

USFT-BROWN-F14S4G6

3 membres

1 tutoriel rédigé

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 2

Total : 608