Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the end of the stylus and remove it from its slot in the midframe.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the rear case by the corner nearest the divot and remove it from the phone.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
If you have an SD card inserted, use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.
-
After the click, release the card and it will pop out of its slot.
-
Remove the microSD card.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the eleven 4.0 mm Phillips #00 screws securing the midframe to the display assembly.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert your plastic opening tool between the midframe and front panel assembly on the side of the phone.
-
Slide the plastic opening tool down the seam.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Continue to run the plastic opening tool down the seam.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Carefully pry around the corner with a plastic opening tool.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pry along the top of the phone with a plastic opening tool.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Push the plastic opening tool down to free the corner of the midframe from the display assembly.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Free the clips along the power button side of the phone.
-
Lastly, free the two clips along the top and bottom edge of battery compartment.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the 3 mm Phillips #00 screw from the speaker enclosure.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using the flat end of a spudger, disconnect the USB board cable connector.
-
Use the tip of a spudger to disconnect the antenna cable connector from the USB board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Push the flat end of a spudger under the USB board to separate it from the display assembly.
-
Annulation : je n'ai pas terminé ce tutoriel.
67 autres ont terminé cette réparation.
10 commentaires
Very good tutorial of the process needed to do this repair. Sadly the one that I was trying to repair had been dropped and the circuit board right where the charge pcb attaches was physically cracked. Did not find that problem until actually removing the original part and throughly inspecting the connect area. Thank You again for an excellent tutorial and dialogue.
Excellent tutorial regarding the disassembly of the Note II and replacement if the charge circuit board. Sadly the device i have had been dropped and the main circuit board where the charge PCB plugs into it was fractured. After removal of the original charge board through inspection noted the original problem was the cracked main PCB. :( Now I have a Note II with a good case and display but damaged main circuit board.
I replaced my USB board and success. However my speakers are not working now. Someone please guide me .
