Aller au contenu principal

Remplacement de l'écran du Samsung Galaxy S7

Ce dont vous avez besoin

Vidéo d'introduction

  1. Remplacement de l'écran du Samsung Galaxy S7, Vitre arrière: étape 1, image 1 de 1
    • Ouvrir votre téléphone endommagera ses joints étanches. Procurez-vous des bandes adhésives de remplacement avant de commencer ou évitez d'exposer votre téléphone aux liquides si vous le remontez sans remplacer les bandes adhésives.

    • Posez un iOpener chauffé sur un bord long du téléphone pendant environ deux minutes.

    • Vous aurez peut-être besoin de refaire chauffer et de réappliquer votre iOpener plusieurs fois jusqu'à ce que le téléphone soit suffisamment chaud. Respectez les instructions de l'iOpener pour éviter de le surchauffer.

    • Un sèche-cheveux, un pistolet à air chaud ou une plaque chauffante peuvent aussi faire l'affaire, veillez cependant à ne pas surchauffer le téléphone – l'écran OLED et la batterie à l'intérieur craignent la chaleur.

    I used a heat gun and heated it a little too much. The color of the rear glass is just a sticker on a clear cover. Due to this I tore the sticker off. Now the back cover is see through, which isn’t a bad thing but the repair was for a customer.

    Kevin Bishop - Réponse

    When using the iOpener, you may need more than 30 seconds, especially in compact or low wattage microwaves. Take this slowly, though, and be extremely careful, as it is easy to overheat your iOpener. Remember, you can always heat it up a tad more, but you cannot undo overheating it.

    Jacob Pratt - Réponse

    I used an adjustable heat gun and set it to 400 degrees (F). That was enough to seperate the glass without having to worry about exposure times of the heat. The front of the phone was just fine. Just be ready to use a bunch of picks to slide in between because they will be needed this way.

    Ryan Schumerth - Réponse

    I went from the bottom center up, using one ifixit tools, one suction cup and one pick.

    Pick just popped in with some minor pressure.

    Laid heat pack along base of phone 2 mins first and worked up slowly, rotating picks as I went. Had to heat iopener over several 30 second bursts

    Lauren Burt - Réponse

    This is useless because the phone does not recognize the new battery and will behave like on the old one

    Search for “battery count xda"

    Albert Einstein - Réponse

    That is an interesting discovery! Thanks for pointing it out—I’ll have to look into it.

    Even if this is true, replacing the battery should still give restore a significant amount of life, since the max voltage affects a minor amount of the battery’s capacity. If you charge a worn battery and a new battery to the same lower max voltage, the worn battery’s voltage will dip more under use and will be depleted faster.

    Arthur Shi -

    Thanks for the guide! It helped me replace a friend's battery with no problems!

    Darren Crook - Réponse

    I will never replace a screen again, and don’t recommend it. Not for phones nowadays. Once upon a time everything was screwed together, and you might even get the same quality or better screen when buying from eBay. And having the phone repaired was nearly the cost of the phone. Now, it’s the reverse. Removing the glued back and screen and cleaning off all the glue for a clean re-seal is an ordeal that takes multiple hours, AND, often the screen you buy on eBay is NOT OLED, but an LCD, and a blurry one at that. And the local phone repair store will replace the screen with an OLED, reliably, same day turn around, for not much more than the cost of an actual OLED screen, because they have the parts in bulk, and the tools and experience to do it quickly. Never again!

    domarius - Réponse

    have you ever had one that just wont open at all? i can not get mine to open to replace the battery i have heated with a heat gun and attached suction cup and it will not lift at all

    Carla James - Réponse

    Hi Carla,

    I've definitely had that experience before. The adhesive is very strong, and the curved back makes getting the initial seam very difficult. I'd suggest focusing on one small area on the edge. Apply steady force when you pull, and repeat a few times to loosen the adhesive. Eventually it will give and present a small gap.

    Arthur Shi -

  2. Remplacement de l'écran du Samsung Galaxy S7: étape 2, image 1 de 3 Remplacement de l'écran du Samsung Galaxy S7: étape 2, image 2 de 3 Remplacement de l'écran du Samsung Galaxy S7: étape 2, image 3 de 3
    • Quand la panneau arrière est chaud au toucher, posez une ventouse le plus près possible du bord chauffé du téléphone, tout en évitant le bord incurvé.

    • La ventouse n'adhèrera pas correctement à la partie incurvée du verre.

    • Si le panneau arrière du téléphone est fissuré, il se peut que la ventouse n'adhère pas. Essayez de le soulever avec du ruban adhésif épais ou de fixer la ventouse avec de la colle forte que vous laissez durcir avant de procéder.

    • Soulevez la ventouse et insérez un médiator sous la vitre arrière.

    • La vitre arrière risque de se briser si vous forcez ou essayez de faire levier avec un outil métallique.

    • En raison de l'incurvation du verre, vous devrez insérer le médiator vers le haut, et non à plat par rapport à la surface du téléphone.

    • Si vous avez du mal, refaites chauffer la vitre pour que l'adhésif continue à ramollir, puis recommencez. L'adhésif refroidit très vite, vous devrez donc peut-être répéter la procédure plusieurs fois.

    • Une autre option pour faire ramollir l'adhésif est de faire couler quelques gouttes d'alcool isopropylique dans l'espace créé en insérant le médiator.

    Because of the metal lip around the phone the picks were to thick to get under the glass. Couldn’t get the glue loose enough with the iOpener or the glass lifted high enough with the suction cup despite using a lot of heat and stength on the suction. Ended up having to use a thin piece of metal to get the first separaration. After that the picks are ok to use.

    loadinglevelone - Réponse

    This step is certainly giving me trouble. I don’t have enough hands to be able to both form the space and to insert the pick. In order to even form the space, I need to use the double-sided plastic scraper-thing.

    Damian Amerman-Smith - Réponse

    Turns out that three hands was the answer. I had my dad insert the pick while I pried open a gap, and it was smooth sailing from there.

    Damian Amerman-Smith -

    How do you pull on the suction cup? I.e. what's the right technique to pull up the suction cup? Just pulling up is going to lift the entire phone, unless I had some kind of double sided suction cup up keep the phone stuck to the table.

    Thank you

    A X - Réponse

    I'm going to try it Jerry rig everythings technique. https://m.youtube.com/watch?v=kHzmFPoZbC... unfortunately every iFixit video seems to use the clamp which seems like an oversight for a tutorial. But it is not fair for me to be too annoyed since they have really good repair kits and the repair guides are nice.

    A X -

  3. Remplacement de l'écran du Samsung Galaxy S7: étape 3, image 1 de 1
    • Une fois que le médiator est bien inséré sous la vitre, refaites chauffer l'iOpener et reposez-le sur la vitre pour faire ramollir l'adhésif.

    Use a heat gun or hair dryer to soften the adhesive to remove the back cover. The Iopener that you heat up with the microwave takes a very long to accomplish the same task.

    michael kotarba - Réponse

    Keep the heat gun in motion at all times and check the surface temperature of the phone with your hand every few seconds to ensure it does not overheat the plastic and glass and electronics. Use several blue guitar picks to brake the seal of the cover once you have softened the adhesive and popped the seal initially with the suction cups.

    michael kotarba - Réponse

  4. Remplacement de l'écran du Samsung Galaxy S7: étape 4, image 1 de 2 Remplacement de l'écran du Samsung Galaxy S7: étape 4, image 2 de 2
    • Faites glisser le médiator le long du côté du téléphone pour couper l'adhésif.

    • Progressez lentement pour éviter que la pointe glisse hors de la jointure. Si vous avez du mal, refaites chauffer et reposez l'iOpener.

    • Laissez le médiator en place et prenez-en un autre pour l'étape suivante. Laisser le médiator en place empêchera la colle de ré-adhérer après que vous l'ayez séparée.

  5. Remplacement de l'écran du Samsung Galaxy S7: étape 5, image 1 de 3 Remplacement de l'écran du Samsung Galaxy S7: étape 5, image 2 de 3 Remplacement de l'écran du Samsung Galaxy S7: étape 5, image 3 de 3
    • Répétez la procédure précédente pour les trois autres côtés du téléphone.

    • Laissez un médiator inséré de chaque côté quand vous continuez avec le suivant pour empêcher l'adhésif de recoller.

    At about this stage, as I was working on the fourth side, the layer of black paint on the inside of the glass started to separate from the glass, near the edge. I may have overheated the phone (I used a heat gun). Most of the paint layer ended up left behind, attached to the body of the phone, as the glass came away - along with the lens covers of the camera and flash. I removed and discarded as much of the paint as I could using tweezers, a spudger, and cautious heating with the heat gun. I hope the back glass will work OK without it; a clear back cover will be a distinctive design feature! If not I’ll have to get a new one. (Note, some battery repair kits from other suppliers such as Amazon include a replacement back glass, which would help with this issue).

    Michael Field - Réponse

    Hi Michael,

    The glass back would definitely work without the black paint. In fact, there are tutorials online that instruct exactly how to do that in order to have a cool transparent glass back look!

    Arthur Shi -

  6. Remplacement de l'écran du Samsung Galaxy S7: étape 6, image 1 de 2 Remplacement de l'écran du Samsung Galaxy S7: étape 6, image 2 de 2
    • Soulevez la vitre et retirez-la du téléphone.

  7. Remplacement de l'écran du Samsung Galaxy S7: étape 7, image 1 de 2 Remplacement de l'écran du Samsung Galaxy S7: étape 7, image 2 de 2
    • Pour remonter la coque arrière avec les bandes adhésives prédécoupées, consultez ce tutoriel.

    • Si vous nettoyez la surface du châssis central avec de l'alcool isopropylique, veillez à ne pas mettre d'alcool sur la bobine de charge sans fil. Le revêtement de la bobine se décomposera s'il entre en contact avec de l'alcool.

    • Veillez à allumer votre téléphone et à tester la réparation avant de poser la nouvelle couche d'adhésif et de refermer le téléphone.

    • Si vous préférez, vous pouvez remonter votre téléphone sans remplacer l'adhésif. Décollez tous les gros morceaux d'adhésif qui pourraient empêcher la coque arrière de tenir. Une fois installée, faites chauffer la coque arrière et appuyez dessus pour la fixer. Ce ne sera pas étanche, mais la colle est suffisamment forte pour tenir la coque en place.

    Apply heat with iOpener/blower or the isopropyl alcohol on the adhesive you want to remove.

    I did not and noticed I peeled off pieces of the paint coating from the cover glass together with the adhesive.

    Eduard - Réponse

    Do not hold the glass as shown. I did that, and the glass cracked when I tried to pull the adhesive because the adhesive was on tight. Always keep the glass down on a flat surface so that you don’t apply any bending forces to it.

    blicher - Réponse

    I'm sorry to hear that! That's a good suggestion—I'll modify the photo slightly to deter people from holding the glass in the air.

    Arthur Shi -

  8. Remplacement de l'écran du Samsung Galaxy S7, Ensemble antenne NFC et bobine de charge: étape 8, image 1 de 1
    • Dévissez les douze vis cruciformes de 3,5 mm qui fixent l'ensemble antenne NFC et bobine de charge.

    They made a typo I think its supposed to say 1.5 millimeter instead of 3.5 millimeter.

    KaydenFisher - Réponse

    QA sticker over screw on my model (2018). I advise you delicately remove these with something sharp, from the center of the screw outwards. If you stick the screwdriver straight in, the sticker will jam up in the head of the screw and make it much less likely to get a good grip on the screw as it turns, causing it to slip and strip the screw head.

    domarius - Réponse

  9. Remplacement de l'écran du Samsung Galaxy S7: étape 9, image 1 de 3 Remplacement de l'écran du Samsung Galaxy S7: étape 9, image 2 de 3 Remplacement de l'écran du Samsung Galaxy S7: étape 9, image 3 de 3
    • Insérez la pointe d'une spatule (spudger) dans la petite encoche sur la gauche de l'ensemble antenne et soulevez le tout vers le haut et hors du châssis.

    • Retirez l'ensemble antenne.

  10. Remplacement de l'écran du Samsung Galaxy S7: étape 10, image 1 de 2 Remplacement de l'écran du Samsung Galaxy S7: étape 10, image 2 de 2
    • Utilisez l'extrémité plate d'une spatule pour retirer l'ensemble bobine de charge du téléphone.

  11. Remplacement de l'écran du Samsung Galaxy S7, Connecteur de la batterie: étape 11, image 1 de 2 Remplacement de l'écran du Samsung Galaxy S7, Connecteur de la batterie: étape 11, image 2 de 2
    • Avec l'extrémité plate d'une spatule (spudger), débranchez le connecteur de la batterie.

  12. Remplacement de l'écran du Samsung Galaxy S7, Écran: étape 12, image 1 de 2 Remplacement de l'écran du Samsung Galaxy S7, Écran: étape 12, image 2 de 2
    • Débranchez le connecteur de l'écran et de la vitre tactile à l'aide de l'extrémité plate d'une spatule (spudger).

  13. Remplacement de l'écran du Samsung Galaxy S7: étape 13, image 1 de 1
    • Préparez un iOpener et posez-le sur un bord long du téléphone pendant environ 2 minutes.

    • Vous aurez peut-être besoin de chauffer et d’appliquer l'iOpener à plusieurs reprises pour chauffer suffisamment le téléphone. Suivez les instructions de l'iOpener pour éviter toute surchauffe.

    • Il se peut que la colle de l'écran oppose bien plus de résistance que celle de la coque arrière. Si nécessaire, utilisez un sèche-cheveux ou un pistolet à air chaud pour chauffer suffisamment la colle.

    To me, it seems hard not to damage the screen in the process of the consequtive steps. Tiny shiny shards to vacuum.

    I notice in video instructions, removal of battery and motherboard, opening pick inserted from inside out, less or no screen debris caused, but commented is, not to remove the screen unless it is already broken.

    Eduard - Réponse

    STOP. As noted above…Use the Video Method. When I was finally able to begin detaching the screen, the glass separated off, while the screen remained attached. This action sheered of the connection to a front-facing sensor which remained firmly embedded by adhesive to the front glass.

    In retrospect, removing the main board, heating and using picks from the back worked with somewhat less effort and better control.

    Jeffry Long - Réponse

  14. Remplacement de l'écran du Samsung Galaxy S7: étape 14, image 1 de 3 Remplacement de l'écran du Samsung Galaxy S7: étape 14, image 2 de 3 Remplacement de l'écran du Samsung Galaxy S7: étape 14, image 3 de 3
    • Une fois que l'écran est suffisamment chaud au toucher, posez une ventouse le plus proche possible du bord chauffé de l'écran.

    • Si votre écran est fissuré méchamment, il se peut que la ventouse n'adhère pas. Essayez de le soulever avec du ruban adhésif épais ou de fixer la ventouse avec de la colle forte que vous laissez durcir avant de continuer.

    • Soulevez la ventouse et insérez un médiator sous l'ensemble écran.

    insert opening pick down ~30 degrees to go between screen and frame. Parallel to glass went between glass and screen.

    Eduard - Réponse

  15. Remplacement de l'écran du Samsung Galaxy S7: étape 15, image 1 de 1
    • Une fois que le médiator est bien inséré sous l'écran, refaites chauffer l'iOpener et posez-le sur le bord de l'écran pour faire ramollir l'adhésif.

  16. Remplacement de l'écran du Samsung Galaxy S7: étape 16, image 1 de 2 Remplacement de l'écran du Samsung Galaxy S7: étape 16, image 2 de 2
    • Faites glisser le médiator le long du téléphone pour couper l'adhésif.

    • La nappe de l'écran se trouve juste en dessous du milieu de ce côté et risque d'interférer avec votre médiator si vous l'insérez trop profondément.

    • Progressez lentement pour éviter de faire glisser la pointe hors de la jointure. Si vous avez du mal, refaites chauffer l'iOpener et réappliquez-le.

    • Laissez le médiator en place et prenez-en un autre pour l'étape suivante. Laisser le médiator en place empêchera la colle de ré-adhérer après que vous l'ayez séparée.

  17. Remplacement de l'écran du Samsung Galaxy S7: étape 17, image 1 de 3 Remplacement de l'écran du Samsung Galaxy S7: étape 17, image 2 de 3 Remplacement de l'écran du Samsung Galaxy S7: étape 17, image 3 de 3
    • Répétez la procédure précédente pour les trois autres côtés du téléphone.

    • Laissez un médiator inséré de chaque côté quand vous continuez avec le suivant pour empêcher l'adhésif de recoller.

    • Ne coupez pas trop profondément en haut ou en bas, vous risqueriez d'endommager les capteurs avant ou l'ensemble haut-parleur sur la partie supérieure, ou les touches tactiles sur la partie inférieure du téléphone.

  18. Remplacement de l'écran du Samsung Galaxy S7: étape 18, image 1 de 2 Remplacement de l'écran du Samsung Galaxy S7: étape 18, image 2 de 2
    • Soulevez l'écran du côté opposé de la nappe de l'écran de façon à ce que la nappe serve de charnière quand vous ouvrez le téléphone.

    Screen was adhered to underlying frame, around the battery gap. Pry into and heat that adhesive to loosen the screen there. To me, it seems hard not to damage the screen in the process. Tiny shiny shards to vacuum.

    I notice in video instructions, removal of battery and motherboard, opening pick inserted from inside out, less or no screen debris caused, but commented is, not to remove the screen unless it is already broken.

    Eduard - Réponse

  19. Remplacement de l'écran du Samsung Galaxy S7: étape 19, image 1 de 2 Remplacement de l'écran du Samsung Galaxy S7: étape 19, image 2 de 2
    • Éloignez délicatement l'écran du châssis en prenant soin de faire passer le connecteur de l'écran à travers la fente dans le châssis central.

    • Ôtez l'écran.

    Much of the back part of the display was also glued to the chassis on my phone. Be very careful when removing the bottom adhesive around the capacitive buttons - I thought what I was peeling off was glue and adhesive, but in fact they were the buttons themselves. I inadvertently damaged both and rendered them useless.

    cness846 - Réponse

    Hmmm ok… this isn’t what I see. I seem to have peeled off the glass layer from the display itself. I have a silver looking display to yet remove before I see any of the frame or ribbon cable shown in the picture above. And yet there was indeed black adhesive strip that I was peeling away during this process, so I thought I was doing the right thing.

    domarius - Réponse

    Solved it. I nearly gave up; I had heated it till the frame was almost too hot to touch, not happy with that, as components could be damaged. Also I couldn’t find anywhere to get a spuger or guitar pick into around the edge, it was all too narrow. But eventually I found I could get a guitar pick under the cables at the top of the screen and start peeling from that direction. Also the screen would crack and splinter at this point, so it was important to move slowly and keep the pick flush and not curl it up too much, to crack as little as possible. And of course, minding the part where the cable is connected on the top right. And I covered it in sticky tape because it was splintering everywhere during this process.

    They’re not kidding - the screen does not survive removal during this process, so it better already be destroyed when you do. In fact I even had little pieces of “display” still stuck to the adhesive when I was done. A foldable display this ‘aint.

    domarius - Réponse

    Also I found the best way to clean off the adhesive, every last bit, was to scrape as much as I could off with the guitar pick, then alternate with a cotton swab with rubbing alcohol, a pin to scrape off tiny bits, and a tissue to wipe off loose bits, over and over, to get every last little bit out so the new adhesive will stick cleanly.

    domarius - Réponse

  20. Remplacement de l'écran du Samsung Galaxy S7: étape 20, image 1 de 1
    • Suivez ce lien pour un tutoriel complet d'application d'adhésif sur l'écran.

    • Avant d'installer un nouvel écran, il est nécessaire de retirer toutes les traces de l'ancien adhésif du châssis en faisant spécialement attention aux petits éclats de verre.

    • Après avoir enlevé tous les restes de colle et de verre du châssis, nettoyez les zones d'adhésion avec de l'alcool isopropylique à 90 % (ou plus) et un chiffon non pelucheux ou un filtre à café. Essuyez dans juste une direction, sans faire de mouvements de va-et-vient.

    • Ceci permet de retirer les derniers restes d'adhésif et prépare la surface pour le nouvel écran.

    • Si le châssis est déformé ou s'il reste de la colle ou des éclats de verre, le nouvel écran ne sera pas monté correctement et risque de s'endommager.

Conclusion

Pour remonter votre appareil, posez de l'adhésif sur la vitre arrière et suivez ces instructions en sens inverse.

185 autres ont terminé cette réparation.

Merci à ces traducteurs :

en fr

100%

Ces traducteurs nous aident réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›

Sam Goldheart

Membre depuis le 10/18/12

465 266 Réputation

538 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Staff

136 membres

16 573 tutoriels rédigés

29 commentaires

The screen replacement went smooth. I just wish it included the adhesive. I didn't see the note where the adhesive needed to be ordered in addition to the screen. Otherwise everything went well.

Thanks

march11934 - Réponse

Samsung s7 ekran değişimi orjinal parça satın aldığınız zaman bu kadar uğraşmanıza gerek yok.
Yapıştırıcı da sadece arka kapağı yapıştırmak için gerekli oluyor

CitrusMobil -

For the price of the screen, I can replace it in a Samsung repair center...

I just need to replace the glass, not all of the AMOLED touch screen... :-( Sorry but this didn't help me.

Darky - Réponse

How much cost u paid to service centre for original display for samsung s7

Durgaprasad -

You can not replace just the glass without special equipment (hot plate, laminator etc.)

Dinan Blueje -

I'm wanting to help my friend do this but I don't have a heat gun. Would a blow dryer work to loosen the glue or does it need to be hotter? He got a quote for 200 from a shop to fix it but they said it takes a month…lame! I've replaced screens in many tables and phones and I have all the necessary tools other than the heat gun and the replacement screen components obviously.

Adam Bacon - Réponse

@Adam Bacon Heat guns are quite inexpensive. The model she uses in this video runs about $20 or less in most shops. A blow dryer may work, but it’s difficult to say for certain. The adhesive Samsung uses is pretty robust. If you find yourself fixing a lot of devices you should really consider investing in a heat gun.

E West -

I did this repair. A heat gun isn’t really hot enough to remove the screen without destroying it. A hair drying isn’t going to touch the glue.

armand -

Use a hair dryer and a spudger and a iSesamo to pop that bad boy off. No sense in buying a heat gun for one use.

Chris Pavlik -

It works great I got my Galaxy S7 apart within a hour using a hair dryer

Mikee Sanchez -

I just want to add that if you only need to replace the glass, this is not the guide for you, and the difficulty rating is a 10 of 10. What I would do to replace just the front glass, is to avoid all these steps, and remove the glass from the front. Do not attempt to remove the AMOLED screen, it will shatter in the process of removing it. You will notice in this video, the screen shatters in the bottom left of the phone, behind the glass.

The other issue is that the glass is laminated to a filter, which is backwards from many screens, where the LCD panels are laminated to the filter, and the screen floats. When you buy a replacement glass, you will need one that has the laminated filter attached, or you will need to figure out a way to separate the two pieces. (I could not).

armand - Réponse

armand what did you use to remove the back, i’ve tried the hair dryer with no luck. Thanks;

Maria

nena_boricua52 -

I would also like to point out that both the front and back glass are extremely brittle. If you broke your glass, because the phone landed on its side, then check for spurs. The smallest protrusion will shatter the glass while applying pressure to seal the adhesive application. I had the tiniest of a protrusion, and the back glass exploded. Thankfully, those are cheap.

armand - Réponse

Thank you very much for good instruction

Vedrasco Victor Vasili - Réponse

Guide help, the included heat pack did not. I ended up buying a heat gun instead. Took my time instead of rush it like some places do or they would just replace your phone all together, which is not what you paid for really. Def was tedious.

Quang Pham - Réponse

Really a good guide!

Maybe it could be cool if with the display assembly comes also the rear glass.. because there is a very high probability that it will damage quickly (during the opening)

So, for those who are going to repair their Samsung Galaxy S7.. just be careful with the back glass!

Thank you all ;)

Tishanth Sinnathamby - Réponse

where we can find lcd replacement in good price ?

morpheous22138 - Réponse

Running into bit of an issue, my screen is broken. At the moment I’m finding ways to turn it back on, restart, hard reset and etc. Nothing that will actually turn it all the way off so I can begin taking off the back panel.

Austin Pimentel - Réponse

The safest method would probably be to let the battery run down, to ensure it doesn’t turn back on and short-circuit something. Good luck!

Sam Goldheart -

Étape 2: Quand la panneau arrière est chaud au toucher, posez une ventouse le plus près possible du bord chauffé de l'iPhone, tout en évitant le bord incurvé.

Cette fiche concerne un Samsung Galaxy S7 ? et vous mentionné un iPhone

Fr C - Réponse

Bonjour Fr C !

Un grand merci pour les yeux de lynx et la remarque. J’ai adapté la traduction. N’hésitez pas à corriger directement la prochaine fois que vous remarquez une erreur.

Bonne journée et à bientôt !

Claire Miesch -

well done, easy to do the job.

i used a heat gun instead the iOpener

ultimo99

antonio esposito - Réponse

I had really hard time finding a way to lift the front screen, so I put the flat end of a spudger through display cable opening from the side of the edge and calmly pressed on the screen from underneath.

Rafal Krawczyk - Réponse

Can I use b7000 to glue the display?

Thanks

Alex P - Réponse

Guten Tag

Nach dem Tauschen des Display zeigt es keine Bilder an… Der Touch hingegen funktioniert. Ich habe eine Original Samsung Display gekauft und verbaut. Was könnte da das problem sein?

Ps: Habe schon erfahrung mit mit Displaytauschen.

GitsEine? - Réponse

I bought the complete repair kit since it had the adhesive strips. Didn’t need the tools. It would be good to offer the option of getting the repair kit with adhesive strips but no tools. Replacing the screen itself was pretty straightforward and not particularly difficult. As was stated elsewhere, the real difficulty was with the adhesives. Some more detailed instructions on this would be useful. Seems like there were locations where the adhesive strips overlapped and other places where they left a gap. Finally, I got to ask why Samsung ever did the phone back with the glass? These are so incredibly fragile. I have replaced these on S7s, S7Edges, and S8s. I am an engineer and consider this a real design flaw. Is there an after market back in just plain metal or plastic? Other than that, I love these phones.

dmorsenv - Réponse

English Below

Hallo,

Een paar jaar geleden had ik het scherm laten vervangen van mijn galaxy s7. Nu heeft het scherm lichte waterschade aan de onderkant, (daar is het een beetje beslagen) en de selfiecamera is ook beslagen. Nu werkt alles helemaal prima, alleen soms is mijn scherm zwart, als ik druk op de bovenkant doet het het weer, of soms moet ik een paar keer met mijn telefoon tegen mijn been slaan en doet het het ook weer. Ik denk dat de aansluiting boven een beetje losjes zit. Het touchscreen werkt gewoon terwijl het scherm zwart is. Dus de lichtjes gaan dan soms niet aan. Kan ik dit denk je zelf fixen zonder een nieuw scherm te kopen?

Guido Sol - Réponse

Hi,

A couple years ago I had my screen replaced of my samsung galaxy s7. Now there is some small water damage at the bottom of the screen and the selfiecamera. The screen and camera are still working probably (only the selfie-camera gives vague images). But sometimes the screen is black and when I put pressure on the top of the screen, it is working again. I think it has to do with the connection from the screen to the rest of the phone. The touch screen works when the screen is black. Do you think I can fix this, without buying a new screen?

Guido Sol - Réponse

Suggestions concerning difficulties I encountered.

ad. step 14, insert opening pick down ~30 degrees to go between screen and frame. Parallel to glass went between glass and screen.

ad. step 18, screen was adhered to underlying frame, around the battery gap. Pry into and heat that adhesive to loosen the screen there. To me, it seems hard not to damage the screen in the process. Tiny shiny shards to vacuum.

I notice in video instructions, removal of battery and motherboard, opening pick inserted from inside out, less or no screen debris caused, but commented is, no to remove the screen unless it is already broken.

Eduard - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 31

7 derniers jours : 159

30 derniers jours : 691

Total : 362,868