Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Boutique

Introduction

The watch contains a small, 300mAh lithium-ion battery. Though these batteries will generally last for years, they do have a limit to the number of times they can be charged. As the battery grows older and is charged repeatedly, it may become less and less able to hold a charge. When this happens, replace the battery.

  1. Lay the watch face-down on a flat, stable surface.
    • Lay the watch face-down on a flat, stable surface.

  2. Press the watchband down against the work surface.
    • Press the watchband down against the work surface.

    • Press the tip of a flathead screwdriver against the edge of the spring-loaded holding pin.

  3. With the spring-loaded pin pressed in, the watch band should release easily.
    • With the spring-loaded pin pressed in, the watch band should release easily.

    • Gently pull the band away from the body of the watch.

    • Repeat steps 2 and 3 for the opposite side.

  4. With the watch laying face-down, locate the four screws. They are located on the back of the watch, at the four corners.
    • With the watch laying face-down, locate the four screws. They are located on the back of the watch, at the four corners.

  5. Using a Torx-T5 screwdriver, remove each of the four 4mm screws and set them aside.
    • Using a Torx-T5 screwdriver, remove each of the four 4mm screws and set them aside.

  6. Gently work the plastic opening tool under the top edge of the watch’s back cover.
    • Gently work the plastic opening tool under the top edge of the watch’s back cover.

  7. With the watch’s back cover pried loose, gently lift it away from the front half of the watch. With the watch’s back cover pried loose, gently lift it away from the front half of the watch.
    • With the watch’s back cover pried loose, gently lift it away from the front half of the watch.

  8. Lay both halves of the watch body assembly face down (with internal components facing up).
    • Lay both halves of the watch body assembly face down (with internal components facing up).

  9. Locate the battery on the back half of the disassembled watch body. It is rectangular in shape and located just above the window for the heart monitor.
    • Locate the battery on the back half of the disassembled watch body. It is rectangular in shape and located just above the window for the heart monitor.

  10. Locate the battery’s electrical contacts. They are located next to the heart rate monitor. They roughly form a “+” shape.
    • Locate the battery’s electrical contacts. They are located next to the heart rate monitor. They roughly form a “+” shape.

    • Using the plastic opening tool, gently pry the contacts away from the plastic channel in which they fit.

  11. Gently work the plastic opening tool under the battery.
    • Gently work the plastic opening tool under the battery.

    • Using the plastic opening tool, gently pry the battery up.

    • If replacing the battery, please dispose of it properly. Do not throw the battery in the trash. Contact your local municipality for locations which accept lithium-ion batteries for disposal or recycling.

Conclusion

To reassemble your device, follow these instructions in reverse order.

12 autre(s) ont terminé cette réparation.

Keith Cooper

Membre depuis le 25/09/2014

1 219 Réputation

6 tutoriels rédigés

Équipe

USF Tampa, Team 1-7, Brown Fall 2014 Membre de l'équipe USF Tampa, Team 1-7, Brown Fall 2014

USFT-BROWN-F14S1G7

3 membres

6 tutoriels rédigés

Indicate the tools needed.

Dan Brown - Réponse

Indicate screw measurements to nearest mm.

Dan Brown - Réponse

This is neat and helpful, but where do I find a replacement battery?

joshthehappy - Réponse

Where can I purchase these batteries?

chad flores - Réponse

I purchased my battery on eBay.

Jay -

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 10

30 derniers jours : 18

Total : 8,915