Réparez vos affaires Communauté Boutique

Sceptre X9 Komodo VII Power Supply Unit Replacement

Introduction

Use this guide to remove the power supply unit.

Ce dont vous avez besoin

  1. Sceptre X9 Komodo VII Power Supply Unit Replacement, Stand: étape 1, image 1 de 1

    • Place the monitor face down.

    • Remove the four 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the stand by pulling it out.

    Modifier

  2. Sceptre X9 Komodo VII Power Supply Unit Replacement: étape 2, image 1 de 1

    • Remove two 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the plastic bar.

    Modifier

  3. Sceptre X9 Komodo VII Power Supply Unit Replacement, Board Cover: étape 3, image 1 de 1

    • Using a #2 Phillips screwdriver, remove the six 7mm screws at the circled locations.

    Modifier

  5. Sceptre X9 Komodo VII Power Supply Unit Replacement: étape 4, image 1 de 3 Sceptre X9 Komodo VII Power Supply Unit Replacement: étape 4, image 2 de 3 Sceptre X9 Komodo VII Power Supply Unit Replacement: étape 4, image 3 de 3

    • Pry the monitor using the plastic opening tool to release the clips holding the cover on.

    • There are four clips on each side, four on the top, and one on the bottom.

    • You may hear a loud snapping noise when releasing the clips. Do not be alarmed, it is natural.

    • Once all the clips have been released, remove the cover by pulling it up.

    Modifier

  6. Sceptre X9 Komodo VII Power Supply Unit Replacement: étape 5, image 1 de 2 Sceptre X9 Komodo VII Power Supply Unit Replacement: étape 5, image 2 de 2

    • Using the #2 Phillips screwdriver, remove the one 6mm screw.

    • Unplug the indicated cable by pulling on the base.

    • Slide the cover toward the top of the monitor.

    • Remove the cover.

    Modifier

  7. Sceptre X9 Komodo VII Power Supply Unit Replacement, Power Supply Unit: étape 6, image 1 de 1

    • Using a #2 Phillips screwdriver, remove the two 4.72 mm Phillips screws that hold the power adapter in place.

    Modifier

  8. Sceptre X9 Komodo VII Power Supply Unit Replacement: étape 7, image 1 de 3 Sceptre X9 Komodo VII Power Supply Unit Replacement: étape 7, image 2 de 3 Sceptre X9 Komodo VII Power Supply Unit Replacement: étape 7, image 3 de 3

    • Unplug the seven connections from the power supply unit by gently pulling on them.

    Modifier

  9. Sceptre X9 Komodo VII Power Supply Unit Replacement: étape 8, image 1 de 1

    • Using a #2 Phillips screwdriver, remove the screws and the wire that is attached to the ground.

    • Four 6 mm Phillips screws

    • One 8 mm Phillips screw

    Modifier

  10. Sceptre X9 Komodo VII Power Supply Unit Replacement: étape 9, image 1 de 2 Sceptre X9 Komodo VII Power Supply Unit Replacement: étape 9, image 2 de 2

    • Lift the power supply unit straight up to remove it from the back panel.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 5 autres contributeurs

Jose Carrillo

Membre depuis le 09/26/12

23 Réputation

1 tutoriel rédigé

Badges: 6

+ 3 badges supplémentaires

Équipe

Cal Poly, Team 16-56, Forte Fall 2012 Membre de l'équipe Cal Poly, Team 16-56, Forte Fall 2012

CPSU-FORTE-F12S16G56

5 membres

13 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 2

7 derniers jours : 2

30 derniers jours : 2

Total : 666