Réparez vos affaires Communauté Boutique

Shark Rotator Powered Lift-Away Brush Belt Replacement

Rédigé par : Cameron Ngai (et 2 autres contributeurs)
  • Commentaires : 6
  • Favoris : 0
  • Réparations terminées : 4

Difficulté

Modérée

Étapes

10

Temps nécessaire

30 minutes

Sections

2

Drapeaux

3

Incorrect Tools

Outils incorrects

Participez à l'amélioration de ce tutoriel en utilisant les outils adaptés dans les photos et/ou le texte.

Needs Better Images

A besoin de meilleures images

De meilleures photos amélioreront ce tutoriel. Aider en proposant de nouvelles photos!

Markup Mishap

Problème de balise

Ce tutoriel nécessite de meilleures balises. Améliorez-le en corrigeant ou rajoutant des balises.

Introduction

If the brush does not spin and the motor still works, then the brush belt may be worn down or damaged.

This guide will aid in replacing that belt.

  1. Push lift away button and pull the handle up to separate the body from the wand section. Push lift away button and pull the handle up to separate the body from the wand section.

    • Push lift away button and pull the handle up to separate the body from the wand section.

    Modifier

  2. Push lift away button on the wand then lift up on the top section to separate.

    • Push lift away button on the wand then lift up on the top section to separate.

    Modifier

  3. Tilt the wand shaft backwards for convenient. Tilt the wand shaft backwards for convenient.

    • Tilt the wand shaft backwards for convenient.

    Modifier

  4. Lay the head nozzle piece upside down. Locate and rotate the three gray taps to the unlock position.

    • Lay the head nozzle piece upside down.

    • Locate and rotate the three gray taps to the unlock position.

    Modifier

  6. With your fingers, pry and pull the brush cage open.

    • With your fingers, pry and pull the brush cage open.

    Modifier

  7. Remove the 13 screws (circled in yellow) using a phillips screwdriver. Be sure to keep track of which screws go into which hole.

    • Remove the 13 screws (circled in yellow) using a phillips screwdriver.

    • Be sure to keep track of which screws go into which hole.

    • Remove the one screw (circled in red) that has a Torx head (might be Phillips head on some models).

    • The Torx screw is hidden under a rubber gasket. Carefully, lift up the gasket without damaging it to access this screw.

    • Remove the horizontal screw (circled in orange) that attaches the gray side panel (necessary to remove the white cap on the roller brush in step 8)

    Modifier

    The 13 Philips screws are Torxt 25 screws not philips head screws it’s a Special torx drive tool.

    John Murray - Réponse

    You forgot to explain how to remove the two silver end caps one of them has a philips head screw that has to be removed from the inside,

    and it’s hard to find because it’s usually full of lint.

    John Murray - Réponse

    On model NV 752 the torx screw is a T20, not T25. and it is the screw that is in the middle of the unit, not on the end where the red circle is shown above. This is not for the feint of heart. I have now replaced the roller and I am having trouble putting it back together again.

    I have replaced roller brushes on other vacuums and this doesn’t have to be this difficult people. I love my Shark but may reconsider buying another based on how difficult it is to replace this roller brush.

    Jkg Gardiner - Réponse

    My NV 752 had all Phillips screws - 15 of them total. One is hidden on the belt side almost under the brush--the only one positioned horizontally--and holds the gray side panel that covers the cap discussed in step 8.

    E A - Réponse

  8. Lift up the top cover now that all of the screws have been removed.

    • Lift up the top cover now that all of the screws have been removed.

    Modifier

  9. Pry tab out with a flat head screwdriver or any wedge-like tool.

    • Pry tab out with a flat head screwdriver or any wedge-like tool.

    Modifier

    This step is a bit useless as there is a side cover that does not easily come off workout feeling like you're going to break it. I haven't gotten it off to clean my belt because of this. Any suggestions?

    Chimera - Réponse

  10. Gently press in on brush to detach. Pull brush down and out. Pull brush down and out.

    • Gently press in on brush to detach.

    • Pull brush down and out.

    Modifier

  11. Slide the belt off of the gear.

    • Slide the belt off of the gear.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

4 autres ont terminé cette réparation.

Auteur

avec 2 autres contributeurs

Cameron Ngai

Membre depuis le 27/09/2017

604 Réputation

3 tutoriels rédigés

Badges: 12

+ 9 badges supplémentaires

Équipe

Cal Poly, Team S9-G3, Banghart Fall 2017 Membre de l'équipe Cal Poly, Team S9-G3, Banghart Fall 2017

CPSU-BANGHART-F17S9G3

4 membres

6 tutoriels rédigés

Un commentaire

where did you get new belts? I bought a set from Amazon for a Shark NV752 and the belts are a bit to large.

John Doe - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 9

7 derniers jours : 55

30 derniers jours : 160

Total : 11,599