Aller au contenu principal

SodaStream Source Internal Disassembly

Conditions préalables uniquement
Ce tutoriel est uniquement destiné à être utilisé comme prérequis d'autres tutoriels. Il ne se suffit pas à lui-même.

Ce dont vous avez besoin

  1. SodaStream Source  Internal Disassembly, SodaStream Source  Internal Disassembly: étape 1, image 1 de 3 SodaStream Source  Internal Disassembly, SodaStream Source  Internal Disassembly: étape 1, image 2 de 3 SodaStream Source  Internal Disassembly, SodaStream Source  Internal Disassembly: étape 1, image 3 de 3
    • Push the brass bar, located in the top of the device, out of the carbonating block.

    • You can use the end of your screwdriver to push this piece out.

  2. SodaStream Source  Internal Disassembly: étape 2, image 1 de 3 SodaStream Source  Internal Disassembly: étape 2, image 2 de 3 SodaStream Source  Internal Disassembly: étape 2, image 3 de 3
    • Slide the yellow battery cover up and away to remove it from the device.

  3. SodaStream Source  Internal Disassembly: étape 3, image 1 de 2 SodaStream Source  Internal Disassembly: étape 3, image 2 de 2
    • Unhook the bottom piece of the plastic arm on each side of the device.

  4. SodaStream Source  Internal Disassembly: étape 4, image 1 de 2 SodaStream Source  Internal Disassembly: étape 4, image 2 de 2
    • Lift the top of the plastic arm with the spudger and remove it on both sides.

  5. SodaStream Source  Internal Disassembly: étape 5, image 1 de 2 SodaStream Source  Internal Disassembly: étape 5, image 2 de 2
    • Remove the plastic piece, located near the front of the carbonating block, from both sides of the device using a plastic opening tool or nylon spudger.

  6. SodaStream Source  Internal Disassembly: étape 6, image 1 de 2 SodaStream Source  Internal Disassembly: étape 6, image 2 de 2
    • Remove the plastic oval and the spring within it.

  7. SodaStream Source  Internal Disassembly: étape 7, image 1 de 2 SodaStream Source  Internal Disassembly: étape 7, image 2 de 2
    • Pull the loader tab cover down and away from the rest of the carbonating block.

  8. SodaStream Source  Internal Disassembly: étape 8, image 1 de 1
    • Remove the three 17.9 mm screws located on the right side.

    • These screws may be difficult to access.

  9. SodaStream Source  Internal Disassembly: étape 9, image 1 de 2 SodaStream Source  Internal Disassembly: étape 9, image 2 de 2
    • Unhook the four clips on the top of the carbonating block and remove the plastic cover.

  10. SodaStream Source  Internal Disassembly: étape 10, image 1 de 3 SodaStream Source  Internal Disassembly: étape 10, image 2 de 3 SodaStream Source  Internal Disassembly: étape 10, image 3 de 3
    • Lift the clips located on both sides with the plastic spudger. Slide the front cover off.

  11. SodaStream Source  Internal Disassembly: étape 11, image 1 de 2 SodaStream Source  Internal Disassembly: étape 11, image 2 de 2
    • Unhook the silver spring arms on both sides of the device by pushing down.

  12. SodaStream Source  Internal Disassembly: étape 12, image 1 de 1
    • Grip the right and left sides of the device and pull it into two identical halves.

    • Once these two pieces are apart, all remaining internal components will fall out of the device.

  13. SodaStream Source  Internal Disassembly: étape 13, image 1 de 3 SodaStream Source  Internal Disassembly: étape 13, image 2 de 3 SodaStream Source  Internal Disassembly: étape 13, image 3 de 3
    • Pull the foam pad up and remove it from the front side of the carbonation component.

  14. SodaStream Source  Internal Disassembly: étape 14, image 1 de 1
    • Remove the six 17.7 mm screws from the underside of the loader tab piece.

  15. SodaStream Source  Internal Disassembly: étape 15, image 1 de 3 SodaStream Source  Internal Disassembly: étape 15, image 2 de 3 SodaStream Source  Internal Disassembly: étape 15, image 3 de 3
    • Pull the loader tab out of the nozzle.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Angela Mossgrove

Membre depuis le 02/20/17

1 072 Réputation

3 tutoriels rédigés

Équipe

USF Tampa, Team S1-G4, Leahy Spring 2017 Membre de l'équipe USF Tampa, Team S1-G4, Leahy Spring 2017

USFT-LEAHY-S17S1G4

3 membres

40 tutoriels rédigés

2 commentaires

Bonjour j'ai une pièce à l'intérieur dont je ne retrouve pas du tout la position au remontage.

Pouvez vous m'aider ?

Delphine Renard - Réponse

De quelle partie s'agit-il, peux-tu prendre une photo ?

Toon Konings - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 0

Total : 458