Réparez vos affaires

Droit à la réparation

Boutique

Sony Cyber-Shot DSC-W830 Flash Board Replacement

Rédigé par : Tong Tang (et 5 autres contributeurs)
  • Commentaires : 0
  • Favoris : 0
  • Réparations terminées : 1

Difficulté

Modérée

Étapes

10

Temps nécessaire

15 minutes

Sections

4

Drapeaux

0

Introduction

In order to reach the flashboard unit inside the device you have to first remove the front and back panel, the button board and the top cover of the device.

  1. Slide the lock at the bottom of the camera to "Open".

    • Slide the lock at the bottom of the camera to "Open".

    • The door to the battery pack is spring loaded.

    Traduire

  2. Slide the blue clip up and away from the battery.

    • Slide the blue clip up and away from the battery.

    Traduire

  3. Remove the battery.

    • Remove the battery.

    Traduire

  4. Remove the six 3.5mm Phillips #000 screws. Rotate the lock away from the camera. Rotate the lock away from the camera.

    • Remove the six 3.5mm Phillips #000 screws.

    • Rotate the lock away from the camera.

    Traduire

  6. Pry the device open with the plastic opening tool. There are two clips that help prevent the front panel from separating. There are two clips that help prevent the front panel from separating.

    • Pry the device open with the plastic opening tool.

    • There are two clips that help prevent the front panel from separating.

    Traduire

  7. Remove the two plastic spacers between the front and the back panels. The spacers may fall out when removing the panels. Carefully remove the back panel.

    • Remove the two plastic spacers between the front and the back panels.

    • The spacers may fall out when removing the panels.

    • Carefully remove the back panel.

    Traduire

  8. Gently release the button board from the clips. Be careful when lifting the button board; the ribbon cable will still be attached.

    • Gently release the button board from the clips.

    • Be careful when lifting the button board; the ribbon cable will still be attached.

    Traduire

  9. Disconnect the no-fuss ribbon cable by gently pulling it out of the button board. Disconnect the no-fuss ribbon cable by gently pulling it out of the button board.

    • Disconnect the no-fuss ribbon cable by gently pulling it out of the button board.

    Traduire

  10. Gently pry the flash board up from its clips. Gently pry the flash board up from its clips. Gently pry the flash board up from its clips.

    • Gently pry the flash board up from its clips.

    Traduire

  11. Gently pull out the no-fuss ribbon cable from the flash board. Gently pull out the no-fuss ribbon cable from the flash board.

    • Gently pull out the no-fuss ribbon cable from the flash board.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 5 autres contributeurs

Tong Tang

Membre depuis le 15/09/2016

488 Réputation

4 tutoriels rédigés

Badges: 11

+ 8 badges supplémentaires

Équipe

USF Tampa, Team 17-1, Blackwell Fall 2016 Membre de l'équipe USF Tampa, Team 17-1, Blackwell Fall 2016

USFT-BLACKWELL-F16S17G1

4 membres

6 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 11

Total : 901