Sony Cyber-shot DSC-HX1 Lens Assembly Replacement

Introduction

To take out and replace the lens assembly, you must first completely remove the central motherboard and all other internal components.

Ce dont vous avez besoin

Étape 1 Battery

Sony Cyber-shot DSC-HX1 Lens Assembly Replacement, Battery: étape 1, image 1 de 1

Make sure the surface you place the screen on is clean of debris and dust. Otherwise you risk scratching your screen.
Place the camera with the bottom facing you and the lens facing up.

Modifier

Étape 2

Push down and away from the camera to the left on the indicated indentation in the battery cover. The compartment should slide open as shown.

Modifier

Étape 3

Push the blue tab towards the camera body to the right, while simultaneously pulling out the battery.
The battery is not shown here. However, normally the battery would be in the displayed compartment.

Modifier

I want to know which typa of battery used in DSC -H1 don't cyber shot

Stanzin Wangyal - 4 sept. 2020 Réponse

Which type of battery used in DSC H1

Stanzin Wangyal - 4 sept. 2020 Réponse

Étape 4 Motherboard

Sony Cyber-shot DSC-HX1 Lens Assembly Replacement, Motherboard: étape 4, image 1 de 2

Sony Cyber-shot DSC-HX1 Lens Assembly Replacement, Motherboard: étape 4, image 2 de 2

Close the battery cover by pushing the cover inwards and sliding it to the left to allow more maneuverability when disassembling other parts of the camera.

Modifier

Étape 5

Unscrew the four #00 4.0 mm Phillips screws on the bottom of the camera.

Modifier

Étape 6

Remove the two #00 4.0 mm Phillips screws shown on the side of the camera.

Modifier

Étape 7

Unscrew the #00 4.0 mm Phillips screw on the top next to the view finder.

Modifier

Étape 8

Pull open the plastic port covers on the side of the camera.
Remove the revealed #00 4.0 mm Phillips screw.

Modifier

Étape 9

Sony Cyber-shot DSC-HX1 Lens Assembly Replacement: étape 9, image 3 de 3

Lift the back LCD screen to reveal the back of the camera unit.
Unscrew the three #00 4.0 mm Phillips screws at the edge and center of the back camera unit.

Modifier

Étape 10

Sony Cyber-shot DSC-HX1 Lens Assembly Replacement: étape 10, image 3 de 3

Using the plastic opening tool, pry apart the bottom of the camera at the line between the four removed screws.
Place the camera on its lens and use the plastic opening tool to pry at the crack in the case on all four sides of the camera.
Apply moderate force to the backside of the camera enclosure until the two pieces separate.

Modifier

Étape 11

Remove the #00 4.0 mm Phillips screw and the #00 6.0 mm Phillips screw holding the motherboard to the front enclosure.
Disconnect the eight ribbon cables from their ports on the motherboard.

Modifier

Hi,

It would be nice if the locations of the 4.0 mm & 6.0 mm screws were defined.

Also, additional step, or steps are needed to show locations of eight ribbon cable ports and how best to go about disconnecting the cables without damaging the port connectors.

Jim Fogle - 22 sept. 2016 Réponse

There's one more screw to remove under the ribbon cable top left.

Vincent Montariol - 6 avr. 2019 Réponse

Étape 12

Detach the metal bracket from the enclosure by removing the two #00 4.0 mm Phillips screws.

Modifier

Étape 13

If you feel resistance from the board, double check all screws and cables have been removed to avoid damage.
Completely remove the motherboard by gently pulling the board away from the camera.

Modifier

Étape 14 Lens Assembly

Sony Cyber-shot DSC-HX1 Lens Assembly Replacement, Lens Assembly: étape 14, image 1 de 1

Unscrew the #00 6.0 mm Phillips screw on the left side of the lens.

Modifier

There's two more screws to remove on the top right and bottom right corners.

Vincent Montariol - 6 avr. 2019 Réponse

Étape 15

The lens assembly contains exposed leads to capacitors. Be very careful to avoid contact or discharge capacitors before handling as touching the capacitors could lead to electric shock.
Gently slide the lens assembly out of the front camera housing and remove completely.

Modifier