Menu 

Vos paramètres

Mon établi

Accédez rapidement aux tutoriels, aux pièces et aux réponses correspondant à vos appareils
Mon panier (US Store)

On dirait que votre panier est vide

Parcourez notre boutique

Sony Radio CD player and cassette player CFD-S05 Circuit Board Replacement

Rédigé par : Ian Nussman (et 3 autres contributeurs)
  • Commentaires : 0
  • Favoris : 1
  • Réparations terminées : 3

Difficulté

Modérée

Étapes

10

Temps nécessaire

20 - 30 minutes

Sections

2

Drapeaux

2

Bullets!

Puces !

Une bonne utilisation des balises, de la couleur et/ou du format des puces donnera de la clarté à ce tutoriel !

Markup Mishap

Problème de balisage

Ce tutoriel nécessite de meilleures balises. Améliorez-le par des corrections ou des annotations de balisage.

Outils

Aucun outil spécifié.

Pièces

  1. Unscrew the screws on the top of the radio.

    • Unscrew the screws on the top of the radio.

    Traduire

  2. Open the CD and cassette doors and remove the screws in the compartments. To open the CD door push on the bottom left corner of the CD door. To open the cassette door push the button that is to the left of the pause button.

    • Open the CD and cassette doors and remove the screws in the compartments.

    • To open the CD door push on the bottom left corner of the CD door. To open the cassette door push the button that is to the left of the pause button.

    Traduire

  3. Flip the radio upside down and remove the battery cover. Unscrew the one screw below the batteries.

    • Flip the radio upside down and remove the battery cover. Unscrew the one screw below the batteries.

    Traduire

  4. Remove the top of the radio enough to access the wires for removal.

    • Remove the top of the radio enough to access the wires for removal.

    • Do not forcefully remove the whole top piece of the radio! There will be wires connected to the top cover and circuit board.

    Traduire

  6. Remove all of the wires that are connected to both the circuit board and the underside of the top of the radio by pulling them where they are connected

    • Remove all of the wires that are connected to both the circuit board and the underside of the top of the radio by pulling them where they are connected

    • This should include three sets of red and white wires, one set of white wires, one set of black wires, and two ribbon wires. Some cannot be disconnected from the top piece of the radio. Disconnect these plugs from the circuit board.

    Traduire

  7. Unscrew the screws in the circuit board.

    • Unscrew the screws in the circuit board.

    Traduire

  8. Unlodge the green headphone jack on the back of the circuit board by pulling on the back of the radio and lifting the circuit board up.

    • Unlodge the green headphone jack on the back of the circuit board by pulling on the back of the radio and lifting the circuit board up.

    • This may be a little difficult and don't pull to hard because the radio may crack.

    Traduire

  9. Lift the circuit board out of the radio.

    • Lift the circuit board out of the radio.

    Traduire

  10. Insert and align the new circuit board and screw it down.

    • Insert and align the new circuit board and screw it down.

    Traduire

  11. Reconnect the wires that were unplugged from the prerequisite steps.

    • Reconnect the wires that were unplugged from the prerequisite steps.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

3 autre(s) ont terminé cette réparation.

Auteur

avec 3 autres contributeurs

Ian Nussman

Membre depuis le 25/10/2013

827 Réputation

6 tutoriels rédigés

Badges: 11

+ 8 badges supplémentaires

Équipe

UMass Dartmouth, Team 2-5, Gulbrandsen Fall 2013 Membre de l'équipe UMass Dartmouth, Team 2-5, Gulbrandsen Fall 2013

UMASSD-GULBRANDSEN-F13S2G5

2 membres

6 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 10

30 derniers jours : 59

Total : 3,383