Introduction
Désassemblage complet du Sony Xperia Z3 Compact
Ce dont vous avez besoin
-
-
Faites chauffer pour affaiblir la colle. Si vous utilisez un décapeur thermique, faites-le chauffer à plus de 150°C car la bande adhésive waterproof est assez résistante.
-
Placez la ventouse sur la face arrière et tirez pour insérer votre médiator. Coupez la bande grâce à celui-ci et retirez la plaque arrière.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Sony Xperia Z3 Compact NFC is stuck to the battery and connected with the motherboard by metal springs, so free the connector at first.
-
Remove all five screws from the rear frame.
-
Starting from the left corner, pry up the rear frame. There is no adhesive, so it's not difficult.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Release rear camera connector and take it away easily.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Release all the connectors connecting with motherboard including the LCD screen connector and headphone jack connector. Undo the only screw on the motherboard.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pry up the motherboard from left side but avoid side buttons. It should come off easily since there is no adhesive sticker underneath.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Before removing the whole motherboard assembly, we need to get the motor vibration free from it's sticker. It's not strong and easy to handle.
-
There are front camera, main flex, signal cable and battery come with the motherboard.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Release the connector and remove the camera easily.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
The side buttons are fastened by clasps, which are easily freed. Release the connector and remove the main flex.
-
The main flex is smaller than other Xperia Z series devices.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Detach the connector to the motherboard.
-
Next pull firmly on the two small black tabs protruding from underneath the battery. This stretches the adhesive strip and separates it from the battery and the motherboard.
-
CAUTION: This strip is easily ripped when under tension.
-
If it does rip then a sharp flat piece of metal or a knife should be used to cut through the remaining strip.
-
WARNING: This adhesive is very strong. Too much effort, prying or careless cutting may break the motherboard. The torn cover of the battery in the picture shows how strong the sticker is.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Cut the adhesive under the flex and between headphone jack and midframe. And then pry up the sensors gently and remove the assembly finally.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Heat, cut the sticker and remove it. Notice where the earpiece is and be careful not to separate them when using the guitar pick. It's easy to break the earpiece.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
The earpiece is affixed to the touch panel directly, which is why it not recommended to separate it when disassembling the screen.
-
Merci à ces traducteurs :
13%
Ces traducteurs nous aident réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›
20 commentaires
I LOVE your work Sophia!
PLEASE also do a TOP VIEW shot as it would help me beter to look straight down. With or without tweezers is fine. JUST LOOKING Straight down would be better for so many reasons.
YOU ROCK!
P.S. Or just do a single TOP VIEW at the END like this one from Dillon ! Pretty Please!
Awesome! Very neat, carefully explained with tips. Keep up the good work, you might save so many amateurs/experts & their devices!!!
May I know, what is the size of the 5 screws used on the back frame?
can u guys tell me where i can find rear camera securing bracket cause something happend when i remove it and now my wireless range is a 1 step far from router or i canot connetc to the router ...