Aller au contenu principal

Sostituzione Batteria DualShock 4

Ce dont vous avez besoin

  1. Sostituzione Batteria DualShock 4, Smontare un Controller DualShock 4: étape 1, image 1 de 1
    • Aiutandoti con un giravite Phillips #00, rimuovi le quattro viti da 6.0 mm che fissano la scocca posteriore al controller

    • Non forzare troppo le viti mentre le sviti, o potresti danneggiarne la filettatura, rendendone la rimozione impossibile.

    Yo usé un Phillips #000, ya que el #00 quedaba grande y podía dañar el tornillo.

    Adolfo Gomez Toledo - Réponse

    A plain #0 works way better for me

    Jennica Tapia - Réponse

    I agree with Jennica, it's a #0 screw

    Peeter - Réponse

    to re-torque these PH00 screw... i found 19Ncm to be about the max. (since 27Ncm was too much)

    Dreamcat 4 - Réponse

  2. Sostituzione Batteria DualShock 4: étape 2, image 1 de 3 Sostituzione Batteria DualShock 4: étape 2, image 2 de 3 Sostituzione Batteria DualShock 4: étape 2, image 3 de 3
    • Comincia con l'impugnatura sinistra:

    • Per cominciare, afferra l'impugnatura sinistra del controller.

    • Inserisci uno strumento di apertura in plastica all'interno della fuga, e scivola sino agli sticks.

    • Fai leva sullo strumento per continuare a aprire il dispositivo.

    • Ripeti questi passi per l'impugnatura destra.

    Shoulders are where L1/L2/R1/R2 are, not the %#*@ handles. Confusing instructions.

    foxhoundunit89 - Réponse

    Quick tip: Be VERY careful at this step not to dislodge the tiny spring attached to the L2/R2 buttons. While removing the cover, it's easy to pull off either L2/R2 button. Inadvertently pulling off either button will also remove the tiny spring as well. While not too difficult to reassemble, it's not obvious where the spring goes as the spring is almost completely hidden along the side of the button (on the inside).

    I just successfully completed analog stick replacements for two controllers. I completed the first repair without any trouble but managed to dislodge (and almost lose) the spring on the second time around. Needless to say, I spent some time trying to figure out where the spring is supposed to go (no photos of this anywhere). By sheer luck, I figured it out on my own. :)

    Good luck and take your time--especially the first time!

    Michael Whang - Réponse

    couldn't have posted pics for me? :D

    kimsballs -

    Golden tip but I would add a thing or two.

    Most probably both triggers R1&R2 will stay in lower half of the pad case with springs hanging there.

    You must take them of their lower case sockets before assembly and fit them bellow L1&L2

    When you feel click when fitting them and spring works like on normal assembled pad you're done.

    If thats not the case do not try to assemble lower casing half as triggers will not work properly.

    Simon -

    if you lost the springs unfortunately, the triggers would still work but it is harder to get to the precise digital press. In other words you will have hard time to create a light press than a hard press.

    meaningless -

    My controller broke

    Gary - Réponse

    So what I seem to see a lot of sources fail to mention with this model (and promptly break without noticing) are the two plastic tabs attached to the front shell on either side of the headphone jack ; in order to properly pry that section open, all you need to do is lightly push those plastic tabs in, and the section should open up easily. That seems to be one of the main things that prevent people from prying the shell open.

    The updated models have the tabs as well, but aren’t as stubborn considering the bars between the shoulder buttons on those are inside as opposed to being a part of the shell.

    Hope this helps, and feel free to discuss, especially if you’re more familiar with the issue than me.

    Rifter - Réponse

    Thank you so much for mentioning exactly where the internal tabs are located, I couldn't for the life of me get into the controller otherwise.

    I found using two thin plastic guitar picks, the kind that bend more freely, worked very well to shimmy into place on either side of the headphone jack and pop the tabs to get the device to open.

    I did break a small piece from one of the teeth on the back half of the shell that inserts into the tabs, but I believe this was accidentally done before I came across your comment and was prying with a spudger willy-nilly.

    Gently wiggling the front half of the shell containing the main portion of the electronics allowed me to release the triggers and open the controller the rest of the way.

    Fizzwidgy -

    Very helpful, Rifter. Thank you.

    I found this shell assembly surprisingly difficult to separate if you don’t want to break the hook/tabs (and I’m a mechanic, fwiw). There are two pairs of hooks, and none of them are near the “share” and “options” buttons as Step 3 suggests. Like Rifter mentioned, one pair is on either side of the headphone interface. The other is along the sides, right up near the L and R paddles.

    With whatever tool you’re using (bike-tire levers work for me), pry it under the outside base of one of the handles (not inside), lever the tool downward a bit (controller is right-side-up), and slide it forward toward the L/R paddle. That downward rotation should help ease the tab off the hook. For the headphone tabs, pushing inward on the two top-half joystick mounds will help ease those off of the hooks, but you have to push pretty hard.

    If you get them apart, you’ll then be able to gently wriggle the circuit ribbon connector off of the top-half pc board (don’t use a tool - you’ll break it).

    John Branum - Réponse

    Why is this guide about unlatching the plastic clips before forcing the halves apart, completely separate and just linked here? I missed it and now 3/4 of my plastic clips are broken. It should not be a separate guide, it should be in the main guide, it's only a couple pictures!

    retrorocket160 - Réponse

  3. Sostituzione Batteria DualShock 4: étape 3, image 1 de 3 Sostituzione Batteria DualShock 4: étape 3, image 2 de 3 Sostituzione Batteria DualShock 4: étape 3, image 3 de 3
    • Inserisci uno strumento di apertura in plastica all'interno della fuga, e separa le due scocche in un punto nei pressi di questi bottoni:

    • Tasto Share

    • Tasto Options

    • Adesso separa i due pezzi che compongono la scocca del controller, tenendo sempre presente che saranno ancora collegate tramite un nastrino da circuito.

    • Spesso tre piccoli pezzi cadono dalla scocca. Per evitare che vadano persi, assicurati di lavorare su di un tavolo ben controllato.

    • 2 Molle dei Trigger

    • 1 Estensione di colore Grigio del Tasto Reset

    You can't just pull the casing halves apart. There is a plastic bar that is part of the casing and separates the L1 and R1 buttons from the L2 and R2 buttons. To get this loose, pull the casing outward perpendicular to the L and R buttons until you can slide the L2 and R2 buttons from behind the plastic bar.

    dzturbd - Réponse

    SO yesterday replaced the thumb stick on my controller, and now the R2 button is stuck, know any way to remedy this?

    ScootsMcgoots -

    I know you put a warning, but I lost the grey reset button extension. Any idea where to get a replacement part?

    miamiman77 - Réponse

    Hey, not even sure when you wrote this, but wanted to share my solution for this problem. I lost one of my reset button rubber pieces when I was doing a different repair, and found that a standard bamboo skewer is just about the perfect diameter to function as a replacement. Just cut it to the proper length and you should be able to get it in there and get your reset functionality back.

    tcbrekke -

    You don't really need it. A long paper clip will work fine.

    Ron Smith - Réponse

    I've removed and changed all buttons all seemed ok but now the options and share button don't work, as in when I pressed them down there is no longer a click (bounce) I'm certain it's back in the correct place and I don't think they can be put the wrong way up, does anyone have any advice please :)

    Rachel - Réponse

    My share button stopped 'clicking'. When I stripped the controller down I noticed a small copper coloured dimple on the motherboard was depressed instead of proud like the one for the options button. With bluetack I was able to pull it out but each time I tested it with my finger it clicked once and stayed depressed. I don't think there is a permanent solution to this as it's probably metal fatigue or similar so i put a tiny bit of blue tack overy the dimple so the plunger could push that bit further and hopefully pull it out each time. Seems to work as I reassemble the controller. Fingers crossed it holds out a while! I'd love to know if someone else had a different solution.

    The5HD -

    I had an extra part, and it wasn’t gray. Thank goodness for the picture of the black one. It’s rubbery. The small end should be inserted down towards the gold colored spot. It’s next to the word RESET on the mobo.

    J Coyote - Réponse

    When reassembling: If, like me, your R2/L2 buttons stayed with the bottom of the controller when you took it apart, it will be impossible to reassemble and get the tiny springs back in place.

    To remedy, remove the buttons, and attach them, with the springs correctly placed, to the top of the controller. There are two tiny grooves, one on the button, and one on the controller top, into which the spring fits.

    Jeff Human - Réponse

    Jeff, we owe you a six pack for this comment.

    James Goldie -

    Thank You!! The spring came out and I looked for a way to reinsert it. So I led a thread through its opening (so it couldn´t jump away), and compressed it with pliers. So it was easy to put it in.

    VauWeh -

    Jeff, you've been a wonderfully helpful Human. Thanks for the ingenious tip.

    Kris W -

    Thanks man i was struggling there

    Shut-_-Up -

    My controller broke

    Gary - Réponse

    Something is stopping me from opening it cause it cut both by splitting tools

    Josuke Higashikata - Réponse

    Mine was also really really resistant to being pried open. In the end, i did my best to loosen the entire gap at least once, then inserted along the middle bottom and used more force than i would have been comfortable with. The plastic on the edges is slightly shot now and it’s not as smooth a grip-feeling anymore, but it came apart fine and I didn’t break anything important. There is just a lot of surface for a friction fit like this and the joysticks keep pulling it back down, which in combination makes it really resilliant. In my case it also was exuberated by a minor soda spill along the right handle which ‘glued’ it together, and i imagine that can also happen just with use and ‘hand cheese’, especially on the outer edges. There is a lot of surface area to stick together there.

    Seleen Shadowpaw -

    no advice for disconnecting those? there's a warning that they're there... then all the next steps just have it already separated?

    Rook - Réponse

    The ribbon cable can be removed without having to pull too much https://youtu.be/y40RUDSPeiA?si=9Y3gNB1w...

    Andrea Collet - Réponse

  4. Sostituzione Batteria DualShock 4, Batteria: étape 4, image 1 de 3 Sostituzione Batteria DualShock 4, Batteria: étape 4, image 2 de 3 Sostituzione Batteria DualShock 4, Batteria: étape 4, image 3 de 3
    • Stacca il nastrino della scheda madre che connette entrambi le parti della scocca del controller afferrandolo e tirando con le dita.

    • Ricorda l'orientamento del nastrino, perciò assicurati di reinserirlo nello stesso verso quando lo riconnetterai.

    • Non appena avrai separato le due metà della scocca, metti pure da parte quella superiore.

  5. Sostituzione Batteria DualShock 4: étape 5, image 1 de 3 Sostituzione Batteria DualShock 4: étape 5, image 2 de 3 Sostituzione Batteria DualShock 4: étape 5, image 3 de 3
    • Aiutandoti con delle pinzette a becco inclinato, rimuovi il cavetto della batteria scuotendo leggermente il connettore su entrambi i suoi lati.

    • Dopo che avrai rimosso il connettore dalla scheda madre, la batteria potrà essere rimossa dal controller.

    • Una rimozione brusca e violenta del cavetto della batteria potrebbe deformarne il connettore.

Conclusion

Per rimontare il tuo dispositivo, segui le istruzioni nell'ordine inverso.

205 autres ont terminé cette réparation.

Merci à ces traducteurs :

en it

100%

Ces traducteurs nous aident réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›

Mark

Membre depuis le 01/21/14

7 716 Réputation

7 tutoriels rédigés

Équipe

Cal Poly, Team 6-21, Maness Winter 2014 Membre de l'équipe Cal Poly, Team 6-21, Maness Winter 2014

CPSU-MANESS-W14S6G21

4 membres

40 tutoriels rédigés

29 commentaires

My Dualshock 4 wont turn on after the battery replacement.

Any idea on why this happened?

Alexander - Réponse

have you tried to charge it?

Mohamed Aden -

I had a problem with my console but with your guide it is possible to solve this one I think.

Praska - Réponse

I found a replacement battery here, you have to mod the tray a little, but it works like a champ and doubles the life.

http://www.ebay.com/itm/PS4-Controller-B...

binazriel - Réponse

The x button on my controller want working properly so I ordered new rubber mounts. I followed the guide, taking my time to make sure I didn't damage anything.

With the new rubber in place I put everything back together and the controller was working fine but now I've realised it doesn't charge. The battery goes completely dead and switches off. If I then connect it with usb cable it doesn't charge but will turn on the controller for maybe 10 seconds before switching off again.

Anyone any idea what is going on? Thanks.

Kenny - Réponse

my controller is not starting today

Harry Patidar - Réponse

Did this fix to the letter, controller works now but the light bar does not and I'm unsure if it charges. It shows it's fully charged. Could it be that the micro-usb connection is frapped?

the00brotherhood - Réponse

Ok, so it shows it’s fully charged on the PS4 but the light on the controller is out if I’m reading you right. Method I would use… connect the controller to your computer with a wired cable (eliminating the PS4 from the equation).

Check Device Manager in Windows or System Report on a Mac. Does it show your controller?

Yes = USB port on controller is fine, you may have damaged the LED on it during the repair.

No = USB port may be damaged or the cable may be fried.

Your problem doesn’t seem like it would have anything to do with the USB port. If it works but with no lighting, you should be ok unless you use the controller with the PS4 camera.

Brad S -

The battery outlet got ripped off. Can it still be fixed?

nextinline3900 - Réponse

Anything can be fixed. But without knowing how severe the damage is it’s hard to say how difficult it would be, although it may involve cannibalizing another controller. At this point it may be cheaper to just purchase a new Dual Shock.

Brad S -

Hi I have two PS 4 controller that wont charged. I had checked with all the possibilities before purchasing two new 2000 Mah replacement batterries. But after replacing the old batteries, I noticed that one of them stopped charging. I thought it had reached the capacity to the full, but to my surprise it did not work, the light is just blinking when I turned it on. I reset the unit but remmained the same !!!

Could it be the charging port got damaged ??? Kindly advice

my other controller is still charging and I have not tested it.

Wushangkehan - Réponse

By the way, I plugged into the computer…the device manager did not read the presence of the PS 4 controller , could it be the USB port is damaged ???Kindly advice

Wushangkehan - Réponse

I have a simple question…..I replaced my sons PS4 battery with a replacement battery and charging cable……I plugged it all back in as shown…..Now the controller is working……But the battery level on the console/tv is showing it’s charging…..But it does work…….Any idea or reason why the new battery or controller is showing charging still without being connected to the usb? Ty

myfam73 - Réponse

Be carefull with 2000mah batteries. I’m talking about V2 Dualshock 4. The original battery : 54mm x 35mm x 8,5 mm and 24g with the hardcase. In this space, you can’t have a 2000mah. Check the size of a true 2000mah 3,7v cell, and you will see a really bigger size. So, these replacement batteries with the same look as the original one, are fake ! If they work, because many are dead and don’t work at all, you will never have 2000mah. I found a true new 3,7v li-ion cell on Ebay, that fits perfectly, but it’s a 1500mah, and without a hardcase. I had to weld the original connector, but it fits perfectly. Not any voltage problem. So, if you need a new battery, don’t bought any hardcase version, and check the dimensions and weight.

KOULLIT - Réponse

The blue plastic thingy goes away from the battery. There are letters (maybe symbols) on the ribbon opposite of the blue plastic thingy and they are pointing toward the battery

Ryan A - Réponse

so what happens if your controller requires a smaller insert (that is circular and not a square input [which is provided standard in the 2k mah? Same module number but different connectors?

mhoffmanmobile - Réponse

I had trouble with analoge, I fixed that but FPC (flat connector) on mainboard broken and I soldered new 12 pin FPC on mainboard again, but in reverse!

then I put charging cable and the dualshock did not turn on , and I sensed that the dualshock is heating up, I remove charging cable as soon as possible.

problem is this : negative and positive putted in reverse.

I don’t kwow what happen if I solder new FPC in right position .

Does it work or somethings going to out of service?

sorry formy poor English language .

regards,

Hamed

hamed1379 - Réponse

i struggled with the reassembly; its much easier if you attach the L2 and R2 buttons to the upper half of the controller.

follow these steps:

reattach first the battery, then the cable with the blue pull tab.

then assemble the L2 and R2 buttons as follows: make sure to position the springs in their appropriate slots (especially at the hinge receptecle at the upper shell, align the spring and hinges and push it into the holder.

only then assemble the two body halfes together by first guiding the L1&2 and R1&2 buttons in their correct location. finally slightly bend the long studs into the handle grips and tighten all 4 screws.

wooghee - Réponse

I can’t get the battery connector cable out of the socket. I tried to remove it for 15 minutes and it wouldn’t come out.

marcus2159 - Réponse

After replacing the battery, the controller can only be used while charging with the cable.

What is the cause of this?

RK-pkmn - Réponse

My dualshock 4 is charging but isn't turning on

Derrick Egwalusor - Réponse

How can I check which model/version is my controller? (I dont have the back sticker , it fell out a while ago)

Ariel Peteri - Réponse

Hi! From looking at the V2 guides, I found a couple distinguishing factors in each controller. The body design near the vibration motors, the shape and color of the motherboard, and the shape of the plastic around the triggers are all key features to compare between models. Use photos from our disassembly guides for each model, and compare the parts of your controller to parts sold on this site or elsewhere to identify your model.

Clay Eickemeyer -

As of March 14, 2023, this guide has been updated! Comments regarding step procedures may no longer be relevant.

Clay Eickemeyer - Réponse

Will this guide work with the cuh-zct1e PS4 controller model?

Nick Cellini - Réponse

It's likely to be physically the same. There may be a minor component missing or added between variations of these controllers. But, for a battery replacement, it will be at least close to the same opening process.

Clay Eickemeyer -

Thanks Clay! I'll give it a go and coment here if I come across any devastating differences or difficulties!

Nick Cellini -

Sure thing, I'll watch my notifications. When you do open it up, be mindful of the small shoulder clips. Everything else can be experimented on, without too much risk of breaking clips.

Clay Eickemeyer -

SWo when I pluggeged un the battery you I bought from you I bnlew up my controlner and it smelt fvery bad

gooka booka - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 86

7 derniers jours : 703

30 derniers jours : 3,065

Total : 368,774